Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
If I send 0x33 through the project example in the directory “nRF5_SDK_17.1.0_ddde560\examples\802_15_4\wireless_uart”.I can see the data 0b 61 88 01 34 12 0b 00 0a 00 00 33...
Hey
For nNR2805, using SDK nRF5_SDK_17.1.0, when we include the LESEC Pairing, we got the binary file with a size bigger than the flash size
Should nNR2805 work with the...
What is the behavior if back-feeding the nPM1100's VCC output, such as if VCC is supplied from a external supply and no battery or USB power is present.
I have been bringing...
Hello!
Tyring to configure the uart rx/tx pins pull-up, pull-down or open-drain using the ncs 2.0.2 . So far I couldn't do it. For example "bias-pull-down" seems to have...
Hi there, I'm having trouble programming the Nordic Thingy:53. I've got a nRF53 dev kit connected to it via the 10 pin connector (as per the instructions) and of course I...
hi，
I`m project NRF52840-SDK_17.1.0。 How do DFU use the uart?What applications do I use for Win7?I read a lot of other`s qusedions-answers,but I still don`t know how to...
I have a working project on a custom board based on nRF52832 ( PCA10040, S132). This board is a BLE Peripheral.
My task is to migrate this to a custom board based on nRF52833...
Hello, I've been using the modem library from NCS1.7.0 specifically 'at_cmd.h' and at_notif.h'. Now I'm trying to port to NCS2.0.0 and I believe that the AT CMD interface...
Hi,
I've got a display driven over SPI at 8MHz by the lib LVGL in a dedicated Zephyr thread and an ISR configured on one gpio pin that triggers a short routine registering...
Hi,
I'm testing the matter commissioning from your sample "light_bulb" on the nRF Connect SDK v2.1.0
I have this setup:
- One nrf52840dk flashed with the light_bulb...
Hi, In order to adjust the sound pitch a magnetic buzzer I thought using a PWM could be the right choice. Looking at the nrf5340dk device tree source I've found a pwmleds...
Following Setup:
1.) Building light-switch-app from original https://github.com/project-chip/connectedhomeip Repo for nRF5340 from command line with nRF SDK v2.1.0
2...
Hi,
We are close to going into a certification process but before we start we need to be sure we are not missing out on your recommendations with regards to EMC performance...
Hi,
I get the error like below on the Linux XFCE 64-bit platform (Pardus 21.2 distro latest version). It works fine on Windows but having a problem on linux. How can I solve...
Dears,
Currently, when working with the nRF52833dk, I found some weird behavior.
I tried to run the blink example in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_blinky...
