Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, i am new at nordic. I am working with nRF connect sdk. I am trying to run example applications but the code never runs. I have checked with debug and it never goes to...
I'm using NRF Connect SDK 2.1.0 and a 52840DK. In normal (non-bootloader) mode bluetooth initializes fine (bt_enable succeeds). However, when I start using MCUBoot, bt_enable...
We are experiencing connection issues for specific Android & iPhone but not for others (i.e. Samsung Galaxy S9).
Phones with issues
Android Details
Samsung Galaxy...
Dear,
I have 2 kits nRF52-DK and nRF52840-DK. I want to make simple app for sending data from one kit to another. Is it possible to use only the radio without using BLE...
Hello guys, i currently applying the example about MPU9255 following this: GitHub - Martinsbl/nrf5-mpu-examples
i'm using the app_mpu.c, app_mpu.h, mpu9255_register_map...
Hello,
Just starting off with Nordic hardware and have some basic questions, first my setup:
nrf52840-dk development board
nRF Connect v2.1.0 SDK
Setup to use 2...
Hi all,
I'm trying to turn on the increased voltage for the +3 dBm transmit power. I understand that to do that, I need to set the VREQCTRL register, or associated bit in...
I just tried updating nRF Connect for Desktop from v3.11.1 to v3.12.0. I did not see an option to update, so I uninstalled v3.11.1 before I installed v3.12.0.
I notice that...
For reference I am using NCS v2.0 and VSCode with the NCS extension and coding in C++.
Hi, can you help clarify the expected behavior and usage of the MPSL_TIMESLOT_SIGNAL_RADIO...
Hi, I am using NCS v2 and the VSCode NCS extension writing in C++.
I am seeing Timer0 not fire more than once for me after the MPSL_TIMESLOT_SIGNAL_START event.
Ultimately...
In transmitter and receiver communication of the ESB, the transmitter is configured as TX Mode and the receiver is configured as RX mode. The transmitter sends data to the...
Hi,
We have a project which is based on the example buttonless DFU and I'm currently testing the persistence of the bonding information between nRF and the external BLE...
