Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I've had a lot of success with the nRF51 series but recently came to the conclusion that it isn't suitable for our needs and trying to transition to the nRF52.
I picked...
Hello everyone,
I'm developing my own board using the nRF5340. I am quite lost because of the capacitance matching that I need to perform with the 32M Crystal and the 32k...
Dear all.
I have the nRF52840dk and nrf52833dk kits.
I am having the same problem with this guy. And now my kits lost their Jlink and Com port.
In the answer, I found...
I developed a product on ncs1.9.0. It needs to connect to the nb network and support the gps positioning function. When the device is running, I found a problem that when...
The Zephyr documentation about ADC ( https://docs.zephyrproject.org/latest/hardware/peripherals/adc.html ) mentioned ADC _CHANNEL_CFG_DT usage in device tree and later source...
Hi,
I would like to enable the SAADC to read multiple DPPI channels. I am using a timer to publish multiple channels and my code looks like this:
However, the...
Dear all
I am developing a BLE product, and would like to have a different device name for each unit like Product1, Product2 etc. when advertising, so user can identify...
Hi! We are updating our application from NCS 1.9 to NCS 2.1. In the documentation of the HTTP AT command of the 2.X versions of NCS the XHTTPCRSP notification is documented...
Hi Nordic,
1. I am planning to do DFU update with UART
2. I Build smp_svr and flashed successfully when am using mcumgr its getting NMP Timeout
3. I added CONFIG_MCUMGR_SMP_UART...
Hello,
In my project, I have a device (nrf52833 custom board) which I want to operate in dual role (central/peripheral). I've followed a ble_app_hrs_rscs_relay example...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
