hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I'm trying to send an data array over ble nus.
This didn't work.
I'm also getting this warning.
I'm doing something wrong, but I don't know what. Do I also...
Hello,
I am making a Firmware for the FCC certification, I must emit at 3 different frequency, 2404MHz (ch37), 2440MHz (ch17) and 2480MHz (ch39) on a nrf52832.
I unfortunately...
Hello,
I have installed the NCS toolchain using the Toolchain Manager app. I am using toolchain version 2.0.0. Here is the error I get when running `west status` :
Same...
I received Thingy:53 and tested it by following the Getting started with Thingy:53 SDK documentation.
The problem arises from the sentence below.
Getting started with...
Hello,
I'm using the LTE Link Monitor v2.0.1 with the nrf9160dk_serial_lte_modem_2022-06-02_880c82db application on a nRF9160.
I'm able to establish the connexion and...
I saw a news report on Nordic's official website that Nordic's NB products have passed the certification of Chinatelecom. I wonder if they have passed the certification of...
Is there a way to add an offset to the nRF5340's reported RSSI to compensate for any front end loss or gain the design might have? This is to get to an RSSI value at the antenna...
Hi,
I'm using HID mouse example in SDK17.02.
After downloaded soft device and the application, I add the device in my pc blue tooth. I can see the battery level normally...
Hi,
I'm looking for a product Bluetooth 5.2 Radio System-on-Chip (SoC) which is of automotive type, and their operating temperature ranges are (-40 to +125)
I'm working on Electronic Shelf Label project using Feather nRF52 with Raspberry pi for server connection. I need to Adafruit Feather nRF52 to receive data from raspberry...
Hi Sir,
We follow this link to test the NIDD, but I'm not sure whether it is successful.
1. Can we know the NIDD link successful or not from the log? What can we see if...
Hello, We are using the serial LTE modem on the nrf connect sdk v1.9.1. We are trying to receive a big message on a topic we have subscribe to, but the serial LTE modem crash...
Hi, I'm using SDK17.02 on nRF52810,and I have enabled AIN6 reading the voltage of battery successfully.
Now I need to read another voltage outside at the same time, so what...
I are working with the asset tracker v2 app under the nrf connect SDK v2.0.0. We are using the nrf9160DK as nRF9160DK_nrf9160_ns. The precompiled asset_tracker_V2 .hex file...
