When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Is there a process in place for updating a controller only build via the HCI? My current set up is a 9160 as the BLE Host, a 52820 as the BLE controller, MCUs are connected...
Hello, Im a little confused about the nRF Connect SDK ecosystem.
Currently Im using SES with cloned nRF SDK 15.0.3 for nrf52811, however I would like to start using https...
Hi
I plan to enable hardware flow control in the coprocessor code. After successful compilation and burning, I will use Ubuntu to start wpantund and an error will be reported...
We already made working code with NRF5 SDK. It has added three characteristics to send data via UART from a MCU. Each characteristics for separate purposes, for eg. Characteristics1...
Hello,
I'm selecting crystals for a project with nRF52832QFAA.
I noticed that on the spec the drive levels of HFXO and LFXO are 100uW and 1uW respectively. Should the...
Hi,
I'm trying to integrate https://github.com/nrfconnect/sdk-nrf in version v1.9.1 in my baremetal application (nRF5340 NET and APP CPUs). Where can I find the startup...
Hi,
we are using an nRF52833 for an application where we have a sensors, a USB interface and an SD memory device.
We would like to write and read back sensor values to...
Hi,
I am following the step by step tutorial " Getting Started with Secure DFU Bootloader Step by Step guide "
Before following the above guide I compiled ble_app_blinky...
Hello,
I'm trying to use the VL53L1X Time of Flight sensor on my nRF52DK, but I experience some problems.
Previously, I've successfully used the VL53L1X with an Arduino...
Dear Sirs:
We use nRF52810 as the key chip in our product, however, we need it to be central or peripheral based on user's option.
So, we would like to apply softdevice...
Hello!
I am currently working on doing the smp_svr sample:
I have done these commands so far (on created from sample application):
west build -b nrf52dk_nrf52832 -d...
Hello DevZone,
I am using Segger embedded studio with multiple build configurations for the two chips and I am having some issues to get the program to compile my nRF52810...
I have tested the sdmmc driver yesterday with both, CS Pin tied directly and via an external i2c port expander. TCA6408A.
Worked like charm, but today I wanted to to some...
We are using nRF9160 chip (in own custom board), SDK 1.9.1 board with "serial lte modem" firmware. We are unable to get coordinates using AGPS. I suppose this is due to the...
Hi!
I am going to use nRF52832 in a new product and wondering whether should I base an application on the new or the old SDK. I have to take into account support for DFU...
