When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
We are porting to the nrf52832 an application that needs to sample the SAADC continuously at 200Khz (alternating between two inputs) with dual buffering DMA of let's say 1k...
Hello Devzone Community,
I am developing an nRF9160 based firmware for a battery powered device, and am attempting to examine the firmware using `gdb` at the command line...
I'm developing two products that will communicate via ble_uart. Both products have battery, so I need to reduce consumption as much as possible. I'm currently using nrf52832...
Hello,
Im getting different behavior on my SoC depending on what power source I use. For example I tend to get alot of retranmissions from client to server if I have them...
Hi,
I have taken nrf_connect_sdk_v1.9.1 and build n=my application over it.
When I delete .git file from v1.9.1/zephyr/.git, then my west compilation don't occur.
...
I tried to open a program created by else one. The Output is shown below. I could not understand: Due to which warning abort ? There are many warnings.
Creating solution...
Hello Devzone Community,
My name is Ted, and I am continuing my effort to configure a Zephyr based, Nordic aws_iot sample app based firmware to run and support nRF9160 lowest...
Hey I am using a nrf9160dk and I am trying to get lte-ble to work I get the above assert failed.
Does anyone have an idea how to fix this?
I have the hci_luart file...
Hello,
My group has developed a board using the nRF52840 SoC and we are in the process of transitioning our firmware from the development kit to the custom board. Our firmware...
Hello,
I am trying to run the system_off sample project to measure some low power currents. The sleep works as expected but once it reaches:
It does not go into deep...
If I wan to use the nRF52 as a Radio and not support any protocols.
I am looking to use this as a base band waveform processor and transverting down below 1Ghz.
What is...
I'm attempting to create firmware using nRF Connect SDK. Thoroughly studied these guides:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started...
I'm referring to nRF5 SDK 17.0.2. In 'external/freertos/config/FreeRTOSConfig.h', the value 'configLIBRARY_LOWEST_INTERRUPT_PRIORITY' is set to 0xf, but the nRF51/52 only...
Hello! I'm trying to use this low power UART sample: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/peripheral/lpuart/README.html I have a problem...
