Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi
I was just curious as to whether or not there is a specific reason the Xenon's PWM capabilities are not available with NCS/Zephyr. Is there a hard limitation or is this...
Hi Team,
SDK - 17.1.0
chip -nrf52810
I want to store sensor data (12 bytes) every 30 seconds in flash memory. Once the flash is full, I want to replace the old data...
I'm trying to interface with the ds1339 real time clock to set and read the time for timestamping tasks in ncs 1.8.0. I've found a few tutorials that boil down to:
1....
Hello !
I can see this error event is deprecated.
What other registers can be used if any error occurs during on-fly encryption/decryption process ?
In case of RX ,...
Hi,
I was implementing ZigBee coordinator in nrf connect v1.18.0 to connect sensor which develops from template sample. every thing went fine until I add install code (took...
Hi there!
I face issue with setting the connection using PHY Coded.
I've:
- set the #define NRF_BLE_SCAN_SCAN_PHY 4 (it's Coded one) on Central side.
- forced PHY...
Hi,
I am using nRF52832 EV board (PCA10040 1.2.4) to develop my application.
Also, I am using nRF Connect SDK (version 1.8.0) with VS Code.
After I create the example...
I could not find hardware peripheral use description of Zephyr Bluetooth LE Controller, where would be specified exact instances which are used for nRF52.
I found this link...
I am using NRF5240 board and and the latest Sniffer Software 4.0 (which claims Extended Advertising support).
Able to sniff all 3 advertisement channels (37, 38, 39) and...
Hello I am implementing a battery voltage monitoring function using nrf52840. I am a beginner in hardware development. As the first step of this function, I am currently implementing...
Hi,
According to the Direction Finding White Paper , the CTE is a pure sin function at 2.4GHz. This is mixed with a local oscillator at 250KHz (for 1Mbps PHY) to obtain...
Hi,
I try to disable the reset mode and use the pin 0.18 as an normal input pin.
I'm using nrf52840 development kit (pca10056).
Does someone have i idea to resolve...
I currently have a nRF52832 DK connected to an external board with a BC832 module connected to the nRF52832 DK through a P19 connector. The voltage I have running and connections...
