Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
We have a new product and are looking into OOB pairing for authentication and encryption. All the information about OOB flows back to NFC pairing, but that is not what...
Hi
I am working on an application that uses extended periodic advertising feature of BLE 5. In this sample (periodic sync):
https://github.com/nrfconnect/sdk-zephyr...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
Hello,
I'm wrapping up the layout of a board based on the NRF52832 (DCDC). I've tried to replicate the reference design as close as possible. I'm using Kicad and had to...
Hi,
Referring to the case,
https://devzone.nordicsemi.com/f/nordic-q-a/72660/nrf-connect-sdk-v-1-5-0-how-where-to-change-phy-and-tx-power-for-long-range-application
...
Code is based on Nordic UART Service Client sample on nRF Connect SDK v1.8.0
I am trying to create several client connections for different servers. The code is incomplete...
Hi Nordic team
I tried SDK Connect v1.8.0 ble_peripheral_lbs_coex sample.
It found advertising signal was very weak. The distance between PCA10112 and my phone was 1 meter...
I use PPI for ADC and GPIO pulling. When I connect and then disconnect - nrf52840 not advertise until reset the SoC.
I can connect after reset. But when I disconect then...
I am used to using Segger, but am switching to west for various reasons. The main reason is to create a CI/CD pipeline.
I built a sample project with west, didn't see any...
Hello,
I am new to embedded/BLE development so forgive me for my ignorance on some of these topics. I am creating a fairly simple BLE Peripheral Server device that has a...
I have built and run the application: Asset Tracker v2 using Segger IDE with nRF Connect SDK 1.8.0 , and my nRF9160DK device communicates with the AWS IoT Core topics.
I...
Hello Team,
I have interfaced Oled with NRF52805 on i2C.
I have used SDK 15.1.0. and ble_app_uart example [s112].
My problem :
I have made some customized functions...
Hi everyone,
I'm using SEGGER Studio for development. I wrote a code for accessing Flash memory by modifying flshawrite example in SDK.
Now I want to copy all dependencies...
hi,
How can I access flash memory of nRF52840 while using softdevice ? I just want to read and update two integer values? is there any simple way to do this?
Thank you...
