hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I encountered a problem while trying to flash my PCA10040 nrf52 development kit.
I am able to compile my code in Segger Embedded Studio without a problem. The chip...
Hello:
I am using an nrf52840 on a custom board with W25Q01NV NOR Flash with the Nordic QSPI-NOR driver. Programming is with NCS v 1.8.0 (upgraded yesterday) and the VS...
Hi Team,
I am developing an application that required SPI communication with msp430.
But, some received characters are disorders, I see them by JLinkRTTViewer logs. For...
Hi
I'm using nRF51822 xxAA (256 Kbyte ROM). My code size are 66 690 byte, I'm using IAR.
Application memory setup:
This means that I have 131 KByte code size for my...
Hi,
I'm trying to configure my LTE modem (Icarus Board + nRF 9160 + SDK 1.7) with an external SIM.
For that i have to use the PDP configuration.
I use in my prj.conf...
Hi,
I am using SES and NCS SDK 1.6.1 under Win10.
A GPS module is connected to NRF5340, using an UARTE to communicate. The pin receiving GPS data is P0.31.
It works...
Hello,
I want to make sensor sleep and wake-up according to VDD.
- When VDD is below 2.8V, Sensor sleep.
- When VDD is above 2.8V, Sensor wake-up.
Since my board...
Hello,
We have a question from one of our customers as to whether the 52833 is compatible with the S340 Soft Device. On the Nordic website, it is not listed as a compatible...
Could someone explain how to power the nRF52840 via USB?
Looking at the schematics, and also reading the "objective" spec, I can see that VBUS is connected to the USB input...
Hello,
Since yesterday's update of the nRF connect extension the device name of the target in the "connected" devices screen is updated from nrf9160_xxAA to nrf9160_xxAA_REV2...
Hi Everyone,
I tried to build lpUart example from samples available. I was trying to debug then I got the breakpoint on
"__ASSERT (lpuart, "Failed to get the device...
i was working on nRF52840 and nRF9160 with NCS v1.8.0.
i'd like to find an API to reboot system. so i tried to call NVIC_SystemReset(). it works in my nRF9160 project. ...
I am currently designing a PCB which incorporates the nRF9160, and I would like to know the devices behaviour in between 2.0 V and 3.0 V, as this is below the minimum VDD...
Dear,
We are working on our custom boards to develop a watch product which need external flash memory connected by QSPI interface. In this product, the UI images and font...
