hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
The board connected to the PC for the first time, but after I mistakenly loaded the Bluetooth low energy sample instead, the Power profile on software nrf connected for desktop...
nrf51822's SWDIO/nReset pin is controled by a MCU GPIO output, a 1k resistor is in series. SWDCLK is connected to a pull-down resistor. And sometime (very rare) nrf51822 can...
Hi,
I am using nRF9160 multi cell location code on nRF9160-DK PCA10090 version 0.15.0.
Modem FW has been updated to the latest 1.3.1 binary.
I am using LTE-M with AT&T...
Hello there,
Recently I have added and been testing DFU into my existing application. I have conducted a few DFU updates and have noticed a semi-reoccurring issue. I use...
I currently have a working project with ethernet shield ( ENC28J60 ).
I use the driver from NCS 1.5.1.
I want to know how to enable logging?
I found some posts on this...
I am current evaluating the SPIS for the nRF52840 and experiencing incomplete transfers from a connected master (Arduino). I'm sending 'hello world' from the master to the...
I have checked out and built the iBeacon sample in zephyr (samples/bluetooth/ibeacon) for nrfconnect version 1.7.1. I tried building for both the nrf52840dongle and nrf52dk_nrf52832...
Hi,
I have a custom 9160/mfw1.3.1 board with a set of matching networks and I need to setup MAGPIO to control these. This will only be used for cellular, not for GPS.
...
Hello,
We have produced a product that uses the 82520 chip. This product uses the NUS service. We want the Windows PC to use its built-in Bluetooth to connect...
Hello,
I need a PMIC for a lithium polymer rechargeable battery solution.
The nPM1100 from Nordic is interesting, but I see there is a cap on the output current available...
I cannot get the blinky example to work with my NRF52 development kit. I used the example in the pca10040/blank/ses folder and it worked fine. I then modified the code per...
Hi,
I'm evaluating a NRF52833 DK running the peripheral-uart example.
My Galaxy 10E can pair with the DK and the nRF connect Android app on the phone can find it and connect...
Trying to diagnose an issue, and looking for documentation on the memory mappings for the nrf52833 using S140 v7.2.0 - something like infocenter.nordicsemi.com/index.jsp ...
