hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi All!
I have a problem which i can't really understood. I'm using nRF5340-DK evaluation board, and currently i'm trying to get one of timer (TIMER1 in this example)...
Hello,
I have a Nordic connected to a STM32. The DFU procedure on the Nordic works fine and I am able to upload and run a new firmware in buttonless mode. The Nordic also...
nPM1100 use JEITA profile that has charging range 0-60gc. Most batteries has charging range 0-45gc. Is it possible to limit charging to 0-45gc with this chip, or is JEITA...
Hi,
I am developing a product using the SoftDevcie s140 and SDK 17.0.2.
I have the problem, that the standard FreeRTOS port defines configTICK_SOURCE to FREERTOS_USE_RTC...
Hi,
I have a nrf52832 dk(pca10040 1.2.1), use gpio P0.29, P0.30, P0.31 to connect some external device,
external device working voltage is maximum 2.2v, so I connect external...
While running UART rx and tx calls the uart_callback_set I have set during initialization will stop running. This prevents me from sending or receiving any new UART information...
Hello,
Could you tell me if SoftDevice V7.3.0 can be used in SDK 17.0.2?
According to the following website, you should use Softdevice V7.2.0 in SDK 17.0.2.
https...
Hi,
I use a pca10056 with the "mqttsn_sleepy_publisher" example. Unfortunately, I cant connect to the mqttsn gateway. It throws me:
"NRF_LOG_ERROR("CONNECT message could...
Hi,
I am trying to perform buttonless DFU on my NRF52840 DK. I am using SDK 15.30. I performed following steps for DFU.
1. I flashed softdevice S140 6.1.1 using nrf connect...
Hello,
I've been working with a nRF52840DK and the ble_app_uart example (examples\ble_central\ble_app_uart_c) trying to modify it as needed for my application. The dev kit...
These days I have the following problems using NRF_SDH_BLE_OBSERVER. I have a CPP project and try to initialize the BLE-Stack in the following way:
The Project is running...
Hello
I need to use external flash upgrade to be compatible with our old products.I found some information as follows，I can build and download it but I don't know how to...
1.At this link https://www.nordicsemi.com/News/2021/06/Memfault-platform-on-the-nRF-Connect-SDK ， Nordic customers can register 100 devices for free. How to calculate these...
