Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi Support Team,
What's the UBM pad diameter of nRF5340-CLAA?
BTW, any correlation between it and label 'b' in Mechanical specifications in PS?
Best regards
Sal...
When I try to open the .overlay file in SEGGER it shows me an error : "Can't Read file" with the message "Can't open xxxxxx/xxxxx/xxxx.overlay for reading.
Has anyone else...
Hi,
I am running Homekit over Thread sample(NCS/Homekit tag v1.7.0 using MTD-SED conf) on my custom board and I found that the QSPI Flash (MX25R64, as same as the one use...
I want to test OTA in button mode. I have configured the button in DFU project. Now I upload the files in my device in the following pattern:-
1)Bootloader hex file
2...
Hello,
I have an nrf5340-dk board and I am trying to play around with the different baud rates through changing the overlay file (as shown):
I am using teraterm...
Hi guys,
After weeks and weeks of trying with 3 different boards (Thingy91, nrf9160DK and Custom board), combination of different LTE Antennas, Bell, Hologram and iBasis...
I am using nrf52840's dongle development software, and I found that when the slave device sends LL_SLAVE_FEATURE_REQ , the host will return LL_UNKNOWN_RSP. I want to know...
Using the NRF connect app we can simulate the problem we have in our app Cowboy. Some customers cannot pair with the bike that uses the nRF52840. We have secure and non secure...
Hi, I am Marcous.
Currently I am doing multiple beacons (transmitters) in direction finding demos. Since I found that there is no way to simultaneously receive the CTE containing...
Hello there,
We are developing an application which inits all the peripherals and sleeps.
We are initializing:
GPIO's for waking up from interrupt
NFC also should...
Hello,
I am using NCS v1.6.0 for nRF52840.
I need to write 8210 bytes to flash via I2C. I configured the I2C0 with NRFX_TWIM and NRFX_TWIM0 enabled in the prj.conf file...
Bluetooth low energy, Direct Test mode nor RSSI Viewer is working with my nRF5340DK board. For instance with RSSI Viewer it says "Error while setting up device XXXXXXXXXXXX...
Hi
I need to build a communication between nrf5340 and esp32 using UART Protocol. I need to transfer some data from nrf5340 to esp32 and vice versa via UART. Already, I...
I want to add Service based on the Bluetooth base UUID which is 00000000-0000-1000-8000-00805F9B34FB When I am trying to add it using "sd_ble_uuid_vs_add", it always returns...
nrf52805 is being used as a GATT server using a static passkey. An ESP WROOM 32 is being used as a GATT CLIENT. The issues is that nrf52805 sends a disconnect to ESP32 after...
