hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have a theoretical question involving 6 24L01+ devices in PTX mode and one 24L01+ device in PRX mode.
Assuming a synchronized system, when one PTX finishes transmitting...
Hi,
I'm using the NRF9160DK board. I'd like to connect the UART port from 9160 to the 52840. The 9160 is running SLM firmware. The 52840 is running my code.
My question...
Some helpful pictures referenced in documentation (asset_tracker_v2_description.rst) are missing:
missing at least: figure:: /images/asset_tracker_v2_module_hierarchy.s...
I am using below environment for my project
NRF connect for desktop version 3.7.0 and Programmer v1.4.11 in windows 10, NRF52840 and Jlink debugger
I have tried multiple...
Hi!
I have a question regarding the scan timeout. The situation is the following:
On a nRF52840, I repeatedly perform scans every 120s (which is controlled by a CC Interrupt...
hi
I am using nr5340 and it adrvertise as nordic_lbs.. but i want to advertise through beacon sample. it still shows nordic_lbs in my mobile nrfconnect software. but it...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am using SPI...
Hi, my 1-button system off/on example works perfectly fine on nRF52 DK. However, when I move the exact same code to nRF52805, there are some errors.
I choose pin 21 as the...
I've been trying to send fast data with NRF24L01 for a long time. In order for the project to meet its requests, 32bytes of data must be on the Receiver side at a maximum...
At 1M rate, test the reception sensitivity of Bluetooth chip, the number of packets lost at -90dBm exceeded 30.8% as specified by Bluetooth Alliance, and this situation occurred...
hi all, i download the project from github master branch, i also added " pip3 install - r zephyr / scripts / requirements . txt " but still, i got the same issue. i had read...
Hi, I am not sure how to measure the signal strength of the communication within the mesh network (ie. communication between provisioned nodes), in order to verify a change...
Hello all,
Currently I´m developing a code to be load to the SDK to act as a master in a BLE communication. The peripheral is a BLE thermoter that, in order to preform bonding...
