When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
I am trying to figure out a problem with the WDT module behavior
Running on an nrf52832 and using SDK 11 with softdevice s132 v2.0.0!
There are 3 WDT channels...
Hi,
I have nRF52840 DK with Power Profiler PPKI. It was working for long time, but now it suddenly stops working.
Screen saved:
nRFConnect Dektop version 3.7.1, Power...
After I changed from SDK 17.0.2 to SDK 17.1.0 I get for the example project "blinky_FreeRTOS_pca10040" during the compilation with IAR Embedded Workbench IDE - Arm 8.50.9...
Hi, I had designed custom board using icm20948. i tried to get raw values from sensor and succeed then i had ported nucleo code for nrf53 zephyr. when i tried to run below...
Hello,
I'm evaluating nrf52840 and trying to use zigbee/light_bulb as a starting point. One thing I caught immediately and still trying to find an explanation for was the...
Hi DevZone,
I need help to understand the DFU procedure over the Mesh without any second BLE dongle/BLE serial device to populate the DFU packets.
The ask is how can we...
Hi
I am using the nRF52840 with an external sensor which I need to config (nRF is the master). after this, nRF is acting like a I2C slave (twis) and i like to trigger an...
Hi,
I'm making my own program to upgrade the nRF9160's modem firmware over SWD. So far, application note nAN41 has helped a lot, but I'm getting stuck when trying to get...
Hello.
I need to transfer files from a phone to a BLE peripheral device. I have a small FatFS filesystem on an external flash chip on the device, and I'm now trying to decide...
Hi,
I have just setup the nRF Connect SDK for the first time. I am running Ubuntu 20.04 in a Virtual Machine. I followed the instructions in the "Getting Started Assistant...
Hi!
I'm trying to prepare FOTA firmware using instructions provided by: FOTA upgrades but it seems not working.I have couple of issues and questions. Please help me.
My...
Hello,
I have been experimenting with the new VSCode extension for the last week or so and I've noticed some issues. I understand that this is a currently a beta release...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
