Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, I tried to run the ble_app_beacon example (PCA10056e) on NRF8211 chip using SDK 17.1.0. I removed the DEVELOP_IN_NRF52840 and NRFX_COREDEP_DELAY_US_LOOP_CYCLES defines...
I'm trying to flash to a nRF9160 with nrfjprog. The hex file works fine, and can be flashed from other (windows) computers. But any change i'm trying to make with nrfjprog...
When I use this example:ble_central\ble_app_uart_c (SDK_17.0.2 S132 nrf52832)
It disconnects every few seconds and reason 0x8.
LOG :
<info> app: conn_Param Update...
Hello! I'm reading the functions that exist in SPU HAL.
The function nrf_spu_flashnsc_set is used to configuring non-secure callable flash region. Which is great to use...
Hi,
I am using the nRF52833DK with NCS v1.6.1 in SES for a multiperipheral application. The application has the LIS2DH accelerometer which is communicating with nRF52833...
I'm using nrf_sniffer_for_bluetooth_le_4.0.0 on Ubuntu 20.04.3 and running `./nrf_sniffer_ble.py --extcap-interfaces` fails on my system. Which also means the nRF52840 dongle...
Hello,
I would like to implement an I²C communication between a nrf52840 and a MCP3221 (which is an ADC).
The first 7-bit of the MCP3121 are 0b1001101. I guess the slave...
Hi!
I have a custom board based mostly of the nrf9160DK, where I need communication between nrf52849 and nrf9160 processor.
I have used the code from this ticket that...
Hi,
I'm using the PCA10056 dev kit and nRF5_SDK_17.0.2. I am aiming to connect multiple initiators to acceptor using Initiator and Acceptor examples. So far I've been able...
Hi There,
When I am trying to write code, I am not clear about the meaning of the code " bearer_adtype_add( BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME ); "
I try to check the...
I'm using the Zephyr provided WS2812 LED driver (SPI). I am noticing some strange behavior when my chain-length property is greater than 10.
I connected a digital logic...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hello
When I output some data using a 'LOG_xxx' macro, I do get debug information over the RTT console like this:
But as you can see there are some extra bytes in front...
