Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hi Team,
I have using the DK and Source code for ANCS which is given in the SDK. I have to make one statement that, i can able to disconnect an active call using the ANCS...
Hi,
I want to write certain datas frequently to my flash memory of NRF52840 DK and erase it when use is over.Do you have any example codes which i can use for this purpose...
It appears that when setting a GPIO pin up to be used by the GPIOTE module as an output task the GPIOTE module takes over the configuration of the pin. It does not appear...
Can someone tell me how to find the MAC address using Command Line Agent (CLI) because
my sniffer seems to think it is the same as the Extended PANID.
Are they the same...
Hello.
I am working with an nrf52840 Development kit. My objective is to sample data from two ADC channels (the input signal has a maximum frequency of 10kHz) and send...
This is the second time I am posting here related issue on nrf52832 SPI communication. I am still not able to get the response from the sensor. Here I am testing my SPI is...
Hello
I'm going to use the GFX example of sdk v17.0.2 to running the ST7735 TFT LCD display.
I am using Adafruit's 1.8-inch (128*160) display and testing it on the nRF52DK...
I am learning and testing the FOTA function of the 9160. I have verified that it works with the official http_application_update project, but when I test it with my own project...
I want to connect remocon and nrfboard. A nd see the value of the remote control as uart.
so I try to connect remocon and nrf85832 to use SDK 13.1 example.
I use central...
This is a new install of NCS 6.1. Installed using nRF Connect Desktop v3.7.0 Toolchain Manager and connected to a new nRF5340 DK.
I followed the Getting Started, Running...
HI Nordic,
I am working PCA10040, SDK17.0.2, ble_app_uart routine.
I'm try to add ADV/SCAN_RSP data, but when I add some field, such as p_manuf_specific_data or service_data_count...
nrf52840 nrf5_sdk 16.
Looking to use the LPCOMP to wake the nrf from System OFF.
Question: if I config the LPCOMP to use the internal reference "15-level internal reference...
Excuse me:
Suppose I Initialize and turn on UART and the power consumption is 4mA，When I call app_uart_close() the power consumption is 2mA,If I don't initialize UART at...
Hi all,
I have been trying to work with UARTE for both TX and RX, and my test code is working with RX perfectly but not TX, when i try to transmit my data using uart_tx...
