Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello, I recently bought the Laird BL654 DK which is based on the nRF52840. ( www.lairdconnect.com/bl654-ble-modules-and-development-kits) . I was interested in running the...
Hi. We are using the nRF52 sdk v15.2 with S132 v6.1.0 on a nRF52832. Sometimes, when connecting, we get a crash with
identifier 0x1
program counter 0x3FDA
fault information...
Hello,
I'm going to send data from a distance of 100-150m using Bluetooth long range communication.
When I looked up some examples of this, I saw that two development...
Hello!
Running Windows 10, nRF Connect for Desktop v3.7.0, Bluetooth Low Energy v2.5.2.
Have the following section added to the uuid_definitions.json:
The problem...
I am sending data over air from an XBee in transparent mode to an nRF52840 dongle as ZC.
The data is going over the air from the source and destination addresses using a...
Current status. Bond is required to perform FW updates while in OTA mode.
What we want: No Bond is required for FW update in OTA mode, FW files can be uploaded unilaterally...
Hi,
I have questions about the connections between the nRF5340 and the FEM nRF21540.
The nRF5340 has these components:
And the nRF21540 has this component:
I wonder...
Hi everyone,
I am currently reading the nRF53 Series product specification from the info center for evaluation purposes. During reading and looking at the application...
Hello.
Please forgive me for a real beginners question but I would like to understand the relation between the menu configurations in SES and the different configuration...
During a FW update, it failed for some reason and then I couldn't get anything to work. I can't come back from OTA mode. Reset does not work either.
According to the log...
I just found out there is no SPI slave support for SPI3 on NRF52840, but the memory map shows a SPI master for SPI3 though. Is it possible to enable SPI slave on SPI3? We...
Hi,
1. I have implement DFU example without private key (open bootloader !) . How to implement secure bootloader for NCS .
2. when i use the DFU with hid_keyboard the...
Hi! Writing to flash memory. After calling nrf_fstorage_erase (...) a hardfault happens. It only NOT happens if JLink is enabled (using dbg or rtt logs). So I can not debug...
