When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello, I'm building a custom app using the nRF Mesh Library for Android.
I'm using a server database in which I'm storing appkeys and netkeys values so that I can use...
Basically, I cannot do continuous TX with nrf_libuarte_async:
Here is simple reproduce:
It only output ===TICK=== and no +++TOCK+++
Here is what I've tried:
...
Hi,
On the nRF52810, is there any limitation on using P0.12 with I2C? I am using MS50SFA module on a custom PCB.
I've also noticed the same issue on a nrf52 DK while using...
i use ncs1.5.0 and nrf5340dk_nrf5340_cpuapp, i disabled uart0 ,enabled uart3, disabled hci_rpmsg out ,and connect uart3 rx pin p0.32 ,tx pin p0.33 to a 232-usb connecting...
hi
I use nrf52 sdk17. i want to change device name .
1. if device name is less 19, more 18 ,it is ok. for example
#define DEVICE_NAME "123456789123456789" . it is OK...
Hi,
I'm trying to catch my NRF packets with nRF Sniffer for Bluetooth and I can't find them (after starting advertising).
On the other hand - I'm able to connect to the...
Hello,
I am stuck on the step of getting the Thingy91 to start working.
I am following this tutorial: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
i am working on nrf52dk. i have already implemented dfu with button. i want to implement buttonless dfu. as there is a example provided in ble_peripheral with name ...
I'm more of a programmer than an electronics person so I apologise in advance if I misuse terminology or if the answer to this would be obvious if I had more experience. ...
Hello.
I want to raise the SDK version, what should I do at that time? (Example: v16.0.0 → v17.0.2) Should I overwrite all the old SDK sources I'm using with the new SDK...
Hi, I'm using the PWR_MGMT SDK 17.0.2 demo code on my nRF52 DK.
Q1) After enabling parameters in the sdk_config.h, the nRF52 DK could enter the Power Off Mode if I press...
I am trying to conduct a device firmware update using nrfutil's dfu ble functionality. Here is the command:
However, running the above command results in the following...
Has anyone used SDCard interface with either 52840 or 5340 in anything other than SPI mode? I just noticed in the SDK 15.3 code we are using SDCard is in SPI mode. Seems max...
