Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
I try to use 52832 as a frequency meter to measure the bluetooth central frequency to do crystal trimming.
The target is a CW(continous wave) signal, like 2441MHz,which...
Hello, I meet some problem. The chip I used is nRF52810 QCAA, the softdevice I used is s112, I defined P0.09 as SCL and P0.06 as SDA, the TWI can't work and it stops in while...
Short Our project runs application code on the nrf5340 application core and a bt_mesh configuration on the network core. Everything works as expected when we build as two...
Hi, I am Marcous.
Recently I am doing the AoA project in the nrf52833 board. I have now got a antenna matrix, sky13322-375LF , a board with four antennas in it and 4 gpios...
Hello i've implemented a push button detection with the bsp library but i can't fin a way to configure a pullup with it :
When i check the tention on the input it's at...
Hi Nordic DevTeam,
What I have learned from this thread below is that using 32kHz external crystal provides less power consumption and better accuracy :
https://devzone...
To the kind Nordic support team,
We are evaluating a scenario where we need a "gzll gzp host" to receive data on two encrypted pipes at almost the same time (we modified...
i was running some power optimization and MTU tests in NCS V1.5.1 and was able to compile and run.
I upgraded to NCS V1.6.0 and there were several errors
So when I compile...
Hello,
I am currently working with the development board nRF5340DK in order to evaluate the nRF5340 SoC.
Given certain project requirements related to the operating temperature...
Hello,
I am new on Nordic controller platform and i want to make the GPIO pull down and pull up at run time and also change the IO direction.
How i can do that please...
I am using the FAT FS on the nRF9160-DK to store data on an SD card.
The CLIB library provides Linix-like fopen, fclose, …
The flags passed to fopen are strings like ...
hello,
i am using nrf52832 with sdk 15.2 using ble_app_uart example and my beacon stops axdvertsing after sometime can someone help me how can make it advertise continosuly...
I am currently evaluating nrf52840 - CDSENET E73-2G4M08S1C module with installed CircuitPython 7.0.0-alpha.3. Unfortunately the ADC readings are quite noisy. For example for...
