Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am using nrf Connect SDK v1.5.0
The immutable bootloader is located in nrf\samples\bootloader
My question is about the partition setting in the pm.yml.
This...
What is the least latency interrupt that i can implement in external gpio pin? In product specification there are mention about GPIOTE. Is that only way to do it? We need...
I want to receive ADC sampling and transmit UART and Bluetooth.
I think the parameters for Bluetooth transmission are as follows. What are these, and how do you find the...
project ：Zephyr
board ：52840DK
Description ：
we want make 52840Dk advertising only once ，at 37 ，38. 39 channel，so we do like blew
（1）we Start advertising by bt_le_adv_start...
When I look at the zip files that are released for modem updates, I see that they contain a number of files, including delta updates for updates within a major version.
...
Hello,
I'm trying to integrate cli_libuarte on project that use FreeRTOS. I'm basing on example form SDK cli_libuarte how ever this does not use RTOS. What I'm facing is...
Hello!
I'm trying to perform DFU over BLE using a nRF52840-Dongle (PCA10059) devkit. I'm getting the following error:
I've tried to add '-cd 5' and '-f' options...
The OPS states the maximum transmitter RF power accuracy to be +/- 4 dB. Does this imply that if the power is set to +4dBm it could vary from 0 dBm to as much as +8 dBm? What...
The documentation is a little unclear. I am using Arduino Nano 33 BLE. Using the analogread() functions of Arduino I get a much worse performance than the nRF is supposed...
My application is composed by three different source code repositories, organized as follows:
+--- app
L---- lib1
| L-- src
| L-- include
L---- lib2
| L-- src...
This is a bug report for the NRF9160 AWS FOTA implementation tested with nrf-sdk at 25c4404f1
My application is based on the asset_tracker_v2 example.
When I initiate...
I am attempting to develop software for a wearable device that hikers/athletes will use in the case of emergency. It will send out an emergency message when a button is pressed...
Hello,
I am trying to use part of the code from this example https://github.com/zephyrproject-rtos/zephyr/blob/master/samples/subsys/nvs
to write to and read from flash...
Hi
I'm trying to use the battery sample to create some code that reads the battery level at boot. However I'm experiencing what I believe to be a race condition
If I run...
Hi Dev team,
I have been working on a Thingy91and I was trying to read out the battery voltage of the device.
I was able to do that through the modem using the MODEM_INFO...
