Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
We are trying to upload Bootloader only, but it fails with 'Error 5: FW version check failed'. Please view log / pictures.
We have tried to change the bootloader version...
Hello,
there is the following page:
https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library/blob/master/documentation.md
Known issues
Since iOS 13.3 (?)...
Hi all. I've seen a few posts about this, but none of them seem to have the knowledge I'm looking for. I am helping plan a device that has two units and will connect to a...
Hi, guys.
I'm using nRF52 DK (PCA10040) and 16x2 LCD ( ST7032i ). I would like to create a custom icon (e.g. degree Celsus ℃). Here is my code. It doesn't print anything...
Hi,
I would like a solution for encrypted OTA firmware update and I just realized that the Secure DFU doesn't enrypt the firmware image just sign it.
I find this Q&A:...
Is there a way to change the Thread SDK example program (\examples\thread\ncp\ftd\uart) baud from 115200 to a higher 460800? If so, what steps are needed to make this change...
With SDK For Mesh v5.0.0 the replay cache is saved to flash using MESH_CONFIG_STRATEGY_ON_POWER_DOWN. In mesh_config_load() a check is made to ensure that there is enough...
Hi,
I'm working on porting BG95 to nrf52 sdk, it'd be a lot helpful if I can get a head start with some open source implementation(AT parser libraries, drivers porting etc...
Hi,
In the Product Specification for nrf52840 it´s written that setting CONFIG (0x50C) register to Pause (0) would pause the watchdog while the cpu is halted by a debugger...
nrf52840 with SDK15
I am trying to update 3 characteristics if the correct value is written to an authenticated read write characteristic. Actually all of my characteristics...
I'm trying to create a simple point to point link using the nRF24L01+ with a new non-arduino microcomputer. I've searched the internet for example Python programs but only...
Hi,
I would like to double check with you if 9-pin cortex-M adapter board for Jlink can be used and connected to PPK P21 connector : https://www.segger.com/products/debug...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using internal flash one of the sector with start address of 0xfc000.
We have written...
Hello, we are having a low occurrence issue when attempting to write some data in NVM using fstorage.
We are using a nRF52832 as a BLE peripheral using SDK15.2.0 and SoftDevice...
Nordic colleagues,
We just received our nRF 52840 DK and are attempting to install the nRF Sniffer application to use with Wireshark. We were able to program the DK with...
