Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I'm using 2 nRF5340PDK with nRF Connect SDK 1.4.0. 1 PDK with central_uart and 1 PDK with peripheral_uart.
When I change the clock config of the peripheral_uart by using...
using nrf-9160dk and iBasis SIM with pre-built asset tracker app (2020-10-30_5522ca2b) and nrfCloud
First time the device was registered data transmission worked.
Now...
The design has 2 sensors on SPI with mode 3 and the nrf21540 which is mode 0. Can you have 2 different Modes on the same spi bus?
would i use the SPI transaction manager...
Hi,
I have the barest of PCBs with literally just the nRF9160, SIM slot and antenna, and have wired it directly to an Otii Arc, so there is no power circuitry either as...
Hi All,
If I want a Thread device to automatically start commissioning when it starts, is there a code example in Nordic SDK?
Now I just found the API interface, called...
NRF52832 is using the protocol stack and updated by OTA. Why should the number of FDS Pages of the new firmware be equal to the number of FDS Pages of the old firmware?
Hi,
I am using NRF52810 , In my project I need to store Float value and uint32_t value in EEPROM / Flash for permanent storage (Non-volatile storage).
With SDK17 i am...
Installing a toolchain for nRF 9160 is not easy as installing the Arduino IDE ( at the leat in Ubuntu). I request Nordic Semi to install all the required tools in a cloud...
Can I buy nrf52811 in bulk and have my bootloader and firmware installed before I receive them for production? And what is the cost say for 1500 preloaded. ?
Hi
I am new to this forum, I am working on NRF24l01 and having some issues to transmit more bytes, I am suing some sample code which is working for simple transmitting one...
Hello,
The following code was embedded in main function, the sdk version is 15.2.
the debug console show as below:
My question is , why string "This is a string...
Dear all,
after some customs problems I hope I finally will receive my Thingy 91 tomorrow. I have already installed the toolchain and done some readup on the device for...
I am attempting to build the new alexa_gadget example that is included in the nRF Connect SDK.
Environment information:
Windows 64-bit
nRF Connect v3.6.0
nRF Connect...
