hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi Team,
One of my application needs the UART driver in both Interrupt and DMA mode for more data bytes transfer. No need of timeout operation or polling mode.
Can any...
Hello Nordic;
I use SDK 17.0.2 and gls example . We know for security in pairing, considered a password which that is randomly generated in SoftDevice and sent to UART....
I am having problems loading an existing project that I successfully built and ran in the past.
I open IDE from nRF Connect > Toolchain Manager > Open IDE
The SES opens...
Hi,
Our Nordic app is doing BLE<->SPI communication.
All works fine when running in debug mode with SEGGER IDE.
Once we run without the debugger running, the SPI transmits...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
Hi,
I'm using nrf52840 on a custom board and have a sensor connected over the pins P0.9 and P0.10
which are NFC pins that have been converted to GPIO by using macro (CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
which hex file shall i install for an LTE application ?
It is basically step 7 of this tutorial: infocenter.nordicsemi.com/index.jsp
I wanna have a LTE application...
I am trying to start developing on my nRF52833 DK using Segger embedded studios, but my board does not show up as a mounted device on my laptop (echoed by the fact that Segger...
Hi there.
I am attempting to do some reallife tests on the nrf52840, mainly focusing on long-range capabilities and performance between the DK and an iPhone XS. Are there...
Hello, I've seen several posts about this, but I'm a little hesitant to use older posts since you guys put out new and improved versions pretty quickly. We are using SDK 16...
nRF52832 on a nRF52DK connectivity_4.1.1_1m_with_s132_5.1.0.hex pc_ble_driver_py v0.14.2
Steps to reproduce: - connect to a peer device - discover services and attributes...
hello :
1)The packet format of NRF52832 2.4G is as follows, I would like to ask whether the 2.4G CRC can be turned off.
I use two boards PTX and PRX to transmit each...
Hello fellow developers,
I'm developing the Bluetooth Low Energy (BLE) app with my own functions. Now I would like to pack it as a standalone Electron App, which can be...
Dear Sir,
I am working on NRF52 and I have DK of PCA10040 / V1.2.1 / 2017.36 / 682236729. I have done program advertising with scanning both in one program. then I used...
