Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I followed instructions given here https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform-ide
I got it working in Build and Debug mode. However...
Dear Sir,
I am calling the function sd_ble_gap_disconnect() to disconnect the peripheral from the App.
This is called inside ble_evt_handler() function and under
...
I'm looking for Memory LCD shield like using nRF52840 long range demo.
The shield name is probably PCA63520. However I can not find it.
Where can I get it?
In the folder for the sd_api_v6 there are the headers for the softdevice S140: pc-ble-driver_v4.0.0\src\sd_api_v6\sdk\components\softdevice\s140\headers
I have a custom...
I want to use the CUSTOMER[] fields for their apparent intended purpose of storing calibration data in nonvolatile memory. I find it quite absurd that the softdevice would...
Hi,
I am using PWM to control LED power.
The code i use for initializing the PWM is-
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(1000L, PIN1, PIN2); err_code...
Hello,
I am trying to run the example DFU over TFTP. I have setup a tftp server with following configurations:
# /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY...
Hi,
I've followed the link https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral
and added it to uart example...
Hi,
My app requests a timeslot in various conditions - sometimes the timeslot needed is long, sometimes short (unknown a priory) so it asks for the longest possible...
Hi,
Is there any easier way when using Eclipse IDE with GCC for nRF5 SDK 15.2 development to get the Include files in the examples to be recognized easier than tediously...
My set up contains beagle bone black as Application board. PCA10001 board with S120 Softdevice using nordic_sdk_10 running ble_connectivity example program.
I initiated...
I have a Teledyne protocol analyzer for capturing over the air data between an nRF52840-DK and an iPhone 8 device. How do I obtain the encryption key from the nRF52840 SoC...
Hi,
I want to verify Bluetooth on my board is good or bad.
Note that, I do not have any spectrum analyzer or vector network analyzer, just development kit.
I found example...
On the product page the nRF52810 is mentioned as supporting ANT. https://www.nordicsemi.com/eng/Products/nRF52810
However in the info-center looking at the compatibility...
Apologies if this is a Segger question vs a Nordic question.
I have already been evaluating SES for a non-Nordic project, and so it's already installed [on Mac].
I am...
