Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
I’m currently using nrfx libraries when there are no equivalent options in Zephyr drivers, and I found similar drivers with the nrfy prefix. What are the differences...
Hi
I would like to use DeviceTree in VS code. The VS code had installed "nRF Connect for VS Code Extension Pack" and tools chain.
But I can't see any file in "DEVICETREE...
Hi Nordic DevZone Support,
I am facing an issue with my custom PCB using the nRF52840 microcontroller and Zephyr NCS v2.6.1 . The same firmware works on other PCBs , but...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
Hello,
I am trying to build the Wi-Fi Bluetooth LE coexistence example using the nRF54L15 DK and nRF7002 EB, but I encounter the following error: zephyr_pre0.elf section...
This is not a support request.
I just want to share some code that others might find useful. If I post it here then they might find it.
The current RADIO_TEST example...
Hi,
I'm trying to use RTC to generate interrupts at every second. The rtc event handler is below:
In the RTC examples, nrfx_rtc_counter_clear is used to reset the RTC...
We are using the nRF5340 with the nRF7002 Wi-Fi module on our custom board. Our application periodically sends data to a server. During continuous testing, we encountered...
nRF Connect SDK with VSCode has suddenly stopped working.
Problems
When I try to create a new application by copying a sample, it says "no samples available".
When...
I created an application that stress-tests wifi scanning and neighbouring cell scanning, on nrf9151 with wifi extension board. Wifi network scanning and neighbouring cell...
I am using peipheral lbs sample and modifying it for my project use. By default it doesnot has pm_static.yml where addresses could have been defined. Once i build the modified...
Hi everybody,
I have problem with my nrf9151-DK. If I switch my kit do AT-Command mode (I use Serial Terminal of Nordic, v 1.4.3), I am not able to switch my kit to PPP...
I'm porting some code from nRF52832/nRF52840 to nRF54L15 using the MPSL timeslot API. The old code uses MPSL version v2.5.1, the new v2.9.0.
The firmware opens a session...
