When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I'm migrating an nRF52840 project from ncs 2.7.0 to ncs 2.8.0. We pass the board in to the west build command line. Our CMakeLists.txt uses the BOARD & BOARD_QUALIFIERS to...
Hi,
I am refering chapter 3 of "nRF connect SDK Fundamental" . ( Configuration files - Nordic Developer Academy )
I am refering few samples like "blinky_pwm", "peripheral_lbs...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
The scan window does not alternate properly with the BT_LE_SCAN_OPT_CODED option in the scan parameters. Specifically, the scan window does not toggle on and off every 30...
Hi. I want to report 2 observed bugs about board creator wizard of NCS 2.8.0.
1. When you click on "Create a new board", the first thing that you must enter is human-readable...
I'm trying to activate low power mode without success. I found samples but it appears not to work with the last NCS version. I want to get basic GPIO INPUT values at 32khz...
Hi,
1. I am testing nRF54L15 PDK PCA10156 0.8.1 Example is: ncs\v2.8.0\nrf\samples\bluetooth\direct_test_mode 2. Which pins can be used as UART TX and which pins can be...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
Maybe the title doesn't make that clear.
First of all, I have customed my own nrf54l15 board, and I successfully built and run some ncs demos.
Now, I want to do something...
Hello Nordic team,
just received my first hardware and try to port my code which I developed by using the 54L15PDK board with SDK 2.7.0. At the PDK everything did run fine...
Hello,
What is the max data size for NUS?
According to BLE data throughput in the S140 document, it looks like 247 but the data was sent successfully with NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello, I want to configure the radio between two nRF52810 devices. I have an external 32.768 kHz clock and the NN02-101 antenna. My question is: how can I configure the radio...
Hi all,
Ive been able to develop for a few weeks with our nrf52840 device and were able to run our code and do some basic Bluetooth stuff. Suddenly I can no longer flash...
Hi，
How to resolve the following burning errors: PDK:PCA10156 0.8.1
SDK ncs v0.8.0
example :peripheral_uart
Thank you for all your assistance. Kind regards, Peter...
