When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
My task is to use MAX30003 WING and process ECG data using nRF5340 DK. I will use SPI protocol for doing it. I was following these 2 tutorials: Lesson 5 - Serial Peripheral...
I am using SDK v2.5.0 on custom board.
The board has an external 4MB flash chip.
I am wondering though which paritition will be used for the update process, and how that...
My project: I am developing a system consisting of a central and up to 20 peripherals based on the Multi-NUS protocol. Toolchain and SDK : NCS v2.6.1. Development target:...
Hello,
I have a project for the nRF52811 using the nRF Connect SDK. As I understand, it’s not recommended to modify the main .dts file directly; instead, changes should...
Hi Team,
Problem: I'm working on a project using the nRF52840 and nRF Connect SDK 2.2.0. I need to transfer some files from host over UART and store them in LittleFS. I...
We are experiencing interruptions in the audio, with noise similar to popping sounds.
When observing the waveform on the spectrum analyzer during the audio interruptions...
Hello I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle It builds and runs just find on the nRF52840 DK But when I try to build for the dongle...
I made a custom board And I am running the segger example ble_app_blinky_pca10056_s140 But Even if I run log_init();, it returns error code 5 And even if I run timers_init...
Hi,
I have updated the device application firmware from nRF Connect SDK v2.6.1 to v2.7.0.
The firmware was working fine in v2.6.1 without issue. But the same firmware...
mcu: nrf5340
board: nrf5340dk_nrf5340_cpuapp
sdk: v2.6.1
When I configure CONFIG_BOARD_ENABLE_CPUNET to enable cpunet, there isn't an issue. However, when I configure...
Hi, I have been trying to use my esp host mcu with nrf5340dk as a controller.I am using the hci_uart application with CONFIG_BT_LL_ACS_NRF53 =y to include le audio support...
Hi All
I am experiencing an issue with the nRF DFU app (v2.7.0) on devices running both Android 11 and Android 14. The issue occurs when I attempt to perform a DFU update...
