I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello everyone, currently I am writing a program to read the SCD41(I2C) sensor and then use BLE to transmit information. With a separate program in twi_sensor, I see that...
Hello nRF team. Is there any different bewteen passing AT command and directly calling the Modem lbraries APIs(from nRF Connect SDK v2.5.2) to control the modem? For example...
Currently our product shipped with SD132 7.0.1, and bootloader/dfu compiled with SDK 16.0.0
We are testing update the bootloader on production devices, and want know how...
Hi Team, I am trying to do DTM test in NRF 52840 using Zephyr- os .The DTM code is working fine on my dev kit ( NRF 52832).I compiled DTM code for NRF 52840 and changed the...
Hi,
I have a problem with sending over NB-IoT to a cloud service. I have found that the helt of my messages only arrive in the AWS cloud and it seems like the modem also...
Hi Support Team
We use ncs to develop nRF52840 application and want to know how many low power mode do ncs have and how to enter these low power mode.We want the nRF52840...
Hello,
We are searching for a board that supports Angle of Arrival(AOA) and Angle of Departure (AOD) for conducted mode radio testing.We need a board euipped with an antenna...
Dear Nordic team
I have the following code for testing the SPIM function of nRF52832.
NRF_SPIM1->EVENTS_END = 0U; NRF_SPIM1->ENABLE = 0; NRF_SPIM1->ENABLE = (SPIM_ENABLE_ENABLE_Enabled...
Hi Nordic .
We are developing an application with nRF5340. In this application, we need to use the SPI Slave feature. According to the documentation, there isn't a clear...
Hi everybody I'm using sample bluetooth peripheral with sdk v2.6.1 and toolchain v2.6.1 to load with nrf5340 but it doesn't seem to build, I see the library has changed from...
Hi,
I am looking into adding BLE OTA firmware update functionality and started by exploring the example provided in Nordic SDK (SDK v16.0.0) while following the documentation...
i'm trying to get an interrupt using sensor lis2dw12 , i have connected my int1 pin of sensor to my gpio 0.10. whenever data is ready it should give me an interrupt this is...
hello Nordic
i am working with ncs v2.5.0 (with nrf52840 and nrf52832)
i am using the fs_mgmt.c for upload/download files from lfs.
till now used it only on one side...
I have connected BLE device to the Nordic's power profiler kit 2 to do power analysis.
My BLE device advertises every 5 seconds.
I can see current consumption spike every...
