Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
hi，
I want to know how Bluetooth allocates channel resources as a master.
Assuming a Bluetooth master is connected to 8 slaves simultaneously, how does the master allocate...
I am working on a module MS12SF1 which is nrf5340+nrf7002. I set the mac address in the otp by running wifi_radio_ficr_prog otp_write_params command. After restarting the...
On SDK 17.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
Hello,
The following error occurred when I ran the program. 00> <info> peer_manager_handler: Connection security failed: role: Central, conn_handle: 0x0, procedure: Encryption...
Now using 52840(S140_nrf52_7.2.0 protocol stack, SDK:17.1.0) Bluetooth packet sending found that the packet sending data length is far less than the actual length to be sent...
I am using a module named MS12SF1 which is a nrf7002+nrf5340 combine module. For wifi initialization, qspi is used. As it wasn't working I added spi4 in the nrf5340dk_nrf5340_cpuapp...
Hi Support Team
If we use nRF52840 develop BLE peripheral base on NCS. What is the maximum number of phones can connect nRF52840 at the same time? Many thanks.
Hello, I'm working on the nrf7002dk WiFi station sample. Most of the time, data is sent and received successfully through HTTP using the HTTP PUT function. However, occasionally...
Hi everyone.
For FCC testing we are required to create firmware builds to transmit at the beginning, middle, and end of the BLE spectrum to allow the lab to verify duty...
This happened last month also during debugging of . I could not use my device for the whole month because the quota was gone in minutes.
Now, new month, new quota, I turn...
Hello,
I am trying to run the asset tracker v2.
I have completed the setup steps and configuration.
Can you please let me know what to do ?
I have read that the -128...
I am inquiring about the ability to run two different radio protocols from a single nRF52840, based on this little marketing aritcle by NordicSemiconductor . Specifically...
Hi,
I am using nrf52840DK and trying to implement a weather station application using thingy53 application example. I am using a Bosch BME280 sensor and could read the data...
Hi, we are using nRF52832 for our project. SDK version is nRF5_SDK_17.1.0_ddde560. SoftDevice is S132.
The project requires TWI to read data from a sensor and send that...
Dear All:
I found that there is a shell interface for the nrf5340_audio project.
I wanted to test the sd card playback from the shell interface.
For the broadcast sink...
