hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol. ...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
I am running into a recurring issue with attempting to connect to a nRF52840DK advertising using extended advertising from iOS devices. Connections repeatedly fail to establish...
Hello,
I am implementing firmware to communicate using UDP between two nRF7002.
The sender does not know the IP address, so it tries to know the IP address of the receiver...
Hey,
I'm currently working on a legacy project that uses the NRF5 SDK. Rewriting the project to use the nRF Connect SDK would be tedious, time consuming and likely to introduce...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hi,
I'm trying to run `ncs/v2.6.1/nrf/samples/net/azure_iot_hub` sample with `native_sim` board:
1. certificates are configured (compiled in)
2. `zeth` interface is...
I want to use the signing script as mentioned Technical Documentation (nordicsemi.com) , however, with NCS, this script is not automatically being picked up during the build...
Hello,
We have many nrf9160 based devices currently on the market running for our customers. These devices are facing some problems that we are trying to debug right now...
Hello,
I'm having an error when running the spi_flash example on a nrf5340DK.
I added this to the .conf file to have more info:
Here are the console logs:
I'm...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
Hello,
I am running into an issue when I try to use two SPI controllers simultaneously on the nrf5340dk. I am using ncs v2.6.0.
What I am trying to achieve, is a system...
Hi,
I am working on a device that is keyboard like, but it just needs to send one cmd to switch the screen - alt+tab/cmd+tab. I was able to get this working with Windows...
Hi,
I'm trying to FOTA over BLE firmware of mcuboot using NRF52840DK. The project is based on the sample from Intermediate course - Lesson 8, exercise 3 (without the steps...