hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I am evaluating nRF5340 audio dk with CS47L63 DSP. My goal is to find out the MCU processing consumption for LC3 codec what is MCU processing power left for the application...
Hi,
I am writing a program that sends numbers counting up sequentially from my dev board to my phone on 500ms intervals. I used the ble_app_uart example as my base. I am...
Hi all,
I trying to use test-harness v2.6 raspi and nRF52840dk to test commissioning. The result is always failure, and the error is timeout
The firmware DK flash is build...
I have a red pulsating light on the dongle.
dmesg shows it is being detected, on Ubuntu 22.04
[203496.636885] usb 3-3.1: USB disconnect, device number 40 [203508.682046...
Hello,
I have a nrf5340 and pc based on Windows OS. I want to transmit information from 5340 to pc at a speed of 300kbps. Here are my two plans:
Using BLE protocol...
Hi all ,
I had my code working on nRF connect 1.6.0 and now had to upgrade it to work with nRF connect 2.1.2.
I read the migration guide for nRF connect 1.x.x to 2.x.x...
I have tested sending NUS data from nRF52832 to laptop (Windows 10 + Intel core i5), but Windows app doesn’t received all NUS data. But When I tested sending NUS data from...
Hello,
I have downloaded the app for linux from here: https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop/Download?lang=en#infotabs
After downloading...
Hi,
I do have a question about the ble_app_uart for central device. Now it is set to make connection with the periheral based on the UUID. I can't find where in the software...
Hi,
I am writing a program that receives a command from a phone using the BLE UART example. The program can count up or down depending on the command. On every count, I...
Hi,
i'm developing an application that uses scan response.
AFAIK sd_ble_gap_tx_power_set is used to set the advertising tx power (BLE_GAP_TX_POWER_ROLE_ADV).
Is the...
Hello,
I am sunning trying to build the hello world sample as mentioned here:
For this project I am working on ubuntu(VM 22.04.1)
I have followed all the steps as mentioned...
-
Is it better as the ATT MTU size is larger?
I am trying to do nus communication between nrf board 1 and board 2. The data size I want to send is about 30 bytes. Previously...
To make sure that the nRF52840 SoC is not powered when the nRF power switch (SW8) is OFF.
So what happens if I power the nRF52840 SoC when the nRF switch (SW8) is ON ?
