This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi
I am currently running and adjusting the zephyr echo_bot uart sample on my nrf9160 DK. Currently , the sample makes use of UART0 to send a receive information which I...
I'm trying to connect a Thingy91 to the nRF cloud using just in time provisioning. I'm using MoSh. Here is the error:
mosh:~$ cloud_rest jitp Performing JITP... JITP device...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
I am developing a product with nRF52832 in which we need to use the COMP module. We need to route the RESULT signal directly to the RX input of the UART, or to an output of...
Hello,
after upgrading to SDK15 and using the new crypto functionality I experience some weird behaviour during bonding.
Our SW is the peripheral and I am starting the...
We would like configure our device with a public addr instead of the random as is default for NCS/Zephyr. We are currently on Zephyr v3.1.99 and NCS 2.1. I have tracked down...
Hi, https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.1.0/nrf/ug_tfm.html#limitations states that "Firmware Update Services" are not supported. Does it mean that in case...
Hello,
I have compiled the Zigbee ZBOSS NCP HOST on an ARMv7 (32-bit) architecture according to the docs ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/zboss/3.11...
Hi all, I've searched through the devzone but unfortunately my issue is never mentioned.
The problem is: my nRF51 project is converted to a nRF52 project. Pins are all re...
We have a need to use 802.15.4 multiprotocol with BLE, we currently use the 52840 for several products. This uses older SDKs and the 802.15.4 Radio driver with our own MAC...
nRF5 SDK SD140 Using the nRF Connect Android app with the DFU utility, looking at the log I send the Enter Bootloader request and get a thumbs up back (op code = 1, status...
