Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am new to Segger Embedded Studio, I do a test on ble_app_template demo on nRFSDK_v16.0.0 on nRF52840 with S140. There are two configurations of the project, namely Debug...
Hello,
I am getting the following python error when building matter examples using SDK 2.1.0 and MacOS. The same code will build successfully if you open a "terminal" using...
Hi,
I am trying to update the firmware from ble_center to ble_peripheral via BLE DFU(SDK version is "nRF5_SDK_17.0.2_d674dde"),
On the ble_peripheral side I can successfully...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I'm following the tutorial on youtube of Nordic Semiconductor called "Developing Bluetooth Low Energy products using nRF Connect SDK" ( here the link https://www.youtube.com...
I need to use an IPC channel between the Application and Network CPUs to notify one side when the other side has modified data in shared SRAM (region 0x20070000). My system...
Hi,
I am using nCS on nrf52833 based BL653dvk, I am based on default 32kHz CPU frequency. I need to go higher up to 40MHz, kindly suggest what configuration options I...
Hi,
I'm a newbie here.
I have a device using NRF52840 running SDK17 with SD v7 configured as a Central/Observer device doing Active Scan.
I have a few questions:
...
Hello
I am developing a board using nRF52840. I have one doubt i can used internal regulator when i power on vddh and how to select voltage level My requirement is 3.3V...
I want to use UART in the ble_app_multilink_central example. I got the Serial example project working but at the moment of moving all the sdk_config.h flags I just receive...
Hi, I want to my central device to search for peripherals by specific, hardcoced IRKs. I have setup whitelist that cooperates with bonding and peer manager. The thing is that...
I have gone through one example "servo_motor" using PWM method to control motor direction, but that seems little different from what I want to develop.
I am having nRF5340...
Hi,
I´m trying to read my ADC values. I powered de DK with USB and trying to read sensormeasurements, but I can´t see the right values.
I´m trying to read with the 12...
