Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
We manufacture boards based on an NRF52832 and we have an abnormally high rate of BLE faults during tests at the end of production. In order to determine if the problem comes...
Hello,
i'm experiencing a issue regarding receiving UDP responses from our COAP server. Our server implements a piggy back response scheme, however in some cases it is either...
hello
i'm use the nRF5_SDK_17.1.0 and nRF52DK.
I am developing using SDK example , "ble_app_hids_keyboard".
There is only one problem I have to ask.
Check out the...
Hi,
in the ticket here it was reported that the fix for the external flash problem was supposed to be fixed in 2.1.0.
Is that still the goal ?
Can i kindly have an estimation...
Hi,
I'm using nRF52805. I need to advertise BLE continuously according my application but also have to reduce power consumption because device is battery operated.
Currently...
Hi,
today I faced a rather strange problem when trying to restart the SAADC.
Bit of context: a requirement for the product I'm developing changed and the device now must...
Hello,
Can raw data be published via MQTT with SLM 1.7?
In later versions we have done this by entering data mode, which we see is not implemented here.
Is there another...
I'm using the nRF52832 in an energy harvesting application, where I need to cold-start the device and set a GPIO output high in under 50ms in order to latch the power supply...
When using AT command to send data, the baud rate is set to 9600, and the two modules are connected at different temperatures, and the data is sent through the serial debugging...
Hello everyone
The company I work for produces an nRF52840 based dongle.
We also have a bootloader which is a modified sdk example.
We need to save some important data...
I'm trying to install nrf-command-line-tools_10.17.0_amd64.deb on an up to date Debian 11, but dpkg always fails with this error:
# dpkg -i nrf-command-line-tools_10.17...
Hi there,
We appear to be having the same issue as described here and here on a nrf9160 DK. There was no clear changes to hardware at all. LED5 suddenly does not seem to...
Hi Nordic support,
I have been evaluating the nrf5340 audio DK and recently run into a build issue with the example application. I have been able to successfully build...
The following error occurred after BLE APP connects to nRF52832 device. How can debug this issue?
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at ..\..\..\..\..\..\components...
Hi.
I'm trying to include MCUboot in my application following this guide but I get this error:
I'm using version 1.8.0 of the nRF Connect SDK with a project using spm...
