Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
HI
1. If we choose a 28.8MHz crystal oscillator for the MCLK of I2S, will it affect BT? 2. In our design, the power supply is VBAT, and the VDD_nRF setting is 1.8V. Does...
I would like to use GPIOTE, PPI, and TIMER to do the following.
I'm using three GPIO pins. Each pin will get square-wave like signals of varying frequency. On each pin I...
Hi Nordic:
we want to add timesync function on nrf5340 ble nus.(1central + 16peripherals, 0.1ms precision )
Such as:
https://github.com/nordic-auko/nRF5-ble-timesync...
Hi,
Can I know how to set the UICR as the default address in nRF52840 SOC with SDK 17.02/17.1.0 by using nRFJPROG command line tool / SEGGER Embedded Studio IDE.
nRFJPROG...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi, i was working on a project and from one day to the next i am no longer able to flash my DevBoard.
When pluging it in it comes up as "E:\" name JLINK as always, but west...
We have a board that is to be certified by a Chinese test lab, so I need to create an image based on the direct_test_mode sample.
In Zephyr v2.0.0 I created a custom board...
Hello,
We are using nRF Connect SDK 2.0 on an nRF52832 and were wondering if it is possible to use BLE and Shockburst simultaneously? If I compile enabling both Shockburst...
Hello,
A couple of days ago I run the examples direction_finding_connectionless_rx and tx on two nRF52833dk successfully, meaning that I could see the CTE info received...
Hello,
I have reconfigured the nrf_dm sample from ncs 2.0.0 to use Zephyr Bluetooth Controller by adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf.
But then it's stuck in this...
i am using the uart0 on a nrf52840 to communicate with an quectel bg95 using async api (dma) on zephyr 3.1.
from the uart interface there are connected rxd, txd, rts and...
Hi,
I am attempting to merge two example programs together and have hit an issue with a hard fault when my timer interrupt triggers.
This works fine in the standalone...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But pm_sec_params_set() returns errCode=0x7. ...
