Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
What I've done
1) Set up ot-br on an Rpi4 by following this guide .
2) Set up a 52840Dongle (plugged into the RPi4) as RCP by following this guide .
3) Installed the...
I'm using SDK 14.2.0.
I'm trying to read the device ID register from ISM330DHCX accelerometer this way:
ret = nrf_drv_spi_transfer(&m_spi[Instance], ®_addr, 1, read_temp...
Hi guys,
So lately, I decided to update the sdk from 4.1.0 to 4.2.0 and there are some problem that I can not solve myself. So I use the macro ZB_ZCL_REGISTER_DEVICE_CB...
Hello,
i've trying to update the codebase of our current project (under development) from NCS 1.9.x to NCS 2.0.x.
I'm experiencing hard fault crashes when I try to perform...
Hello,
I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840. We currently have an instance of CLI running in our executive loop, and it works fine. We'd also like to implement...
I facing the above issue when build a project. The project structure is below. I copied the Git project project to d:can/firmware/zephyr/samples/drivers/can from https://github...
Good day Nordic people, I am facing a problem when erasing or writing to internal flash memory after enabling softdevice. here the details and tests: Setup: - GCC, arm toolchain...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi Support team,
nrf5 sdk for mesh 5.0, nrf5 sdk 17.0.2, s132, SES;
We are trying to understand the LPN feature based on the LPN example because in our scenario there...
We're developing firmware for a custom board that uses the NRF5340. Today one of the developers reported that they were no longer able to communicate with the board over SWD...
Hello, all
I built CLI sample for Openthread, but failed to run, windows 10 couldn't find any nrf52840dongle inserted, and not any log output through RTT.
When I debugged...
Hi guys,
i'm using DFU over serial and i get the error 4 in NRF_DRV_UART_EVT_ERROR.
This was not happening before and suddenly started.
What could be the issue?...
Hi Nordic Support,
I'm running into an issue with ncs v1.8.0 directing log and shell to RTT backend.
Objective: Using nRF NCS / nRF52840dk - I want to dedicate 1x UART...
