Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I got a code that got a main thread with priority 5, and the workqueue function from the location sample with priority 5. The main thread uses the adxl362 sample to...
Hi,
I am trying to interface with the MAX11198 simultaneous dual ADC over SPI. The ADC has two channels and I am able to read values from one channel at a time using the...
Hello there!
I am working on an ANT+ project, and - as I have taken a fairly unexplored development approach, namely integrating nRF5-SDK Code into a main application written...
I'm working with a prototype sensor that changes impedance when environmental conditions change (sorry, can't provide too many details on the sensor itself).
Currently the...
Hello,
Using nrf Connect SDK v1.9.1 Zigbee nrf52840 -DK and Nordic Zigbee coordinator sample. When in terminal sending command BDB START I get " I: Unimplemented signal...
Good Morning,
I'm testing "peripheral_hids_keyboard" with vsc and I would like changed "CONFIG_BT_HIDS_MAX_CLIENT_COUNT" at the value '3'.
In the menu nRF Kconfig(buid...
Running through the Toolchain setup instructions, installing VS Code to a custom location rather than the default location of C:\Users\{Username}\AppData\Local\Programs\Microsoft...
Hello everyone,
I am experiencing issues to get temperature from DS18B20 sensor with a nRF5340 board.
The probleme I have is that the only values my code reads is...
Using the HTTPS sample, the following do or don't work:
1) out-of-the box (google.com) works. 2) change CA certificate to the root for www.apple.com and connecting to...
Hi,
While developing my application for my company on a nRF9160 on a custom board, I came to use the nrfx_reset_reason.h to get my reset cause.
RESETREAS looks as follows...
Hello everyone,
I am working with the nrf52 DK.
I want to know if is possible to have the 5V pin when powering the DK with the Coin cell battery?
If not, how can I power...
Hello. After switching to NCS v2.0.0, we started observing a strange I2C issue - some sensors did not communicate whatsoever, and some sensors worked just fine. Further analyzing...
I have written my own python script that will be used to program devices with some additional data placed in UICR registers like public MAC address, passkey and serial number...
Hello All,
We have a new nRF9160 design - and I've updated the 9160 binaries to version 1.3.2 - on a few PCBA's - we're seeing an error like this:
Initializing COAP connection...
I followed your step by step guide available on your site for installing the SDK and Toolchain. My system are Fedora 36 with VS Code IDE, but the system detects the errors...
