Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I have a weird issue occuring when trying to connect to my MQTT server.
If i run the code on a NRF9160 DK i can connect perfectly fine to my MQTT server calling...
Hi all,
In the nRF9160 https_Client sample, I was able to connect to the server by provisioning a server-matched root certificate to the nRF9160.
Can I connect to an...
I've been playing around with the v1.9.1\zephyr\samples\boards\nrf\system_off\ example code, as I want to implement something similar in my own code. But I want to be able...
Hi
I would like to change my coded PHY layer 1MBps to 2Mbps.
For that, i just change the params BLE_GAP_PHY_1MBPS to BLE_GAP_PHY_2MBPS in my code.
But now the function...
Hi,
We are battling to get to the advertised low power values as described here:
https://devzone.nordicsemi.com/guides/cellular-iot-guides/b/hardware-design/posts/measuring...
Hi
I'm trying to create a central device to connect with a series of different peripheral devices. All the peripheral devices can be discovered during the scanning. However...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hi,
I have previously compiled the zigbee command_line_agent for the PCA10059 which I use for testing.
It worked when uploaded so I have one working PCA10059.
Recently...
Hi,
I have a problem getting interrupts by the rtc component working. I am using the nrf58211 chip, nRF Connect SDK v. 1.9, uBlox BMD360-eval development board.
My code...
I have Windows 7 pc on which PCA10040 DK is used to test UUT.
- Devkit frequently gets corrupted for unknown reason.
-It has custom Firmware which is validated to be working...
I learned today that the ALIGN_NUM macro doesn't work as expected if the data type passed is not unsigned int type. I find that using int32_t or uint8_t with ALIGN_NUM produces...
I'm using nRF Connect for Mobile on my Android smartphone (HTC U11, Android 9) for over a year now
It was working well so far last year, then I paused for a few weeks and...
Is a bootloader required to flash code to the nRF-52832?
I built a custom board with a blank nRF52832-QFAB-R. I'm able to run through the tests on the Segger J-Flash V7...
Hi
I am working with an nRF52DK board that is successfully communicating with Nordic's nRF Toolbox app via BLE UART.
I would like to be able to modify the app as I modify...
