When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello. The problems with starting advertising started after I wanted to add NVS (most likely). The error occurs in the bt_le_adv_start function
What does this error mean...
I am working on a project with the nRF9151 chip. In this chip, I am using the LTE modem in eDRX mode .
Apart from eDRX mode , I also want to put the MCU into sleep mode...
Hi,
I want to use the nRF53 with the timesync demo ( https://github.com/nordic-auko/nRF5-ble-timesync-demo ) to start an I2S task when a timer overflows on the net core...
Hello, The DevAcademy fundamentals lesson 6, example 1 shows how to connect a bme280 to a DK. Then in lesson 6, example 2 it shows how to connect to an onboard light sensor...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. Especially,regarding the configurable bitrate for the LC3 codec in nRF Connect SDK Ver2.8...
Hi
in my application, I need to reduce /disable RAM sections in nRF54L15 to save Idle RAM current. For Example, I need to retain only 64KB RAM when I am in idle.
how can...
Hi folks,
I'm attempting to program an nRF52833 using a Segger J-Link+ connected to the SWD program/debug pins on the board.The board is only an nRF52833 - as a learning...
hi, noted a few things in the Rev 1 Errata v0.8 that might be tricky to solve practically in sw/hw
3.16 [33] RADIO: GPIOs can exhibit radiated emissions
max...
I'm currently attempting to register a service and it's subsequent characteristics statically using variables and not hard coded GATT tabel , I can successfully register an...
Hello,
I've been playing with an nRF54L15 PDK, specifically with the sid_end_device sample. I was having a lot of trouble getting the device to register/connect to Sidewalk...
Dear,
We have project using normal advertisement (not extended) on a nrf5340 module (Raytac MDBT53-1M) to send data using Manufacturer data.
We have a product already...
Hi, Currently Im developing on a custom board that has a NRF52840 and a NRF9160. Both MCUs communicate using UART Async API and I added the support for LPUART on both sides...
Good day, I'm trying to use pin 1.02 as a GPIO in a TF-M build using a (custom) non-secure board target, and I'm struggling to find the appropriate way to accomplish this...
Dear Nordic Team, we are using the adafruit_feather_nrf52840 and nrf52840dk for our prototypes and recently the toolchain around nrf and zephyr has become a problem. Build...