Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I was looking to use the NUS Central project and port it to the PCA10059 (nrf52840 Dongle)
I was going to add the USBD_CDC_ACM so I can port the NUS traffic to a Putty terminal...
Hi,
i have nRF52840 DK.
I am working on radio test code based radio_test example code with nRF5_SDK_17.0.2_d674dde version.
If the transmitter is configured as : (BLEN...
I can't build examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay. I get the following error message:
cc1: fatal error: cannot open 'C:/.../examples...
Hello,
After looking at aws_iot sample files, I've stumbled upon the question regarding how one can dynamically change IDs and certificates for multiple 9160 devices? I...
From yesterdays question https://devzone.nordicsemi.com/f/nordic-q-a/80411/state-of-cs-ss-pin-after-nrfx_spim_xfer I have done a logic measurement and I can confirm that after...
Hi,
schematic for CFAA WLCSP mentioned, QDAA is given in the documentation. I want a reference for Circuit configuration no. 1 schematic for CFAA WLCSP mentioned in the...
Hi
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are trying...
Hello!
I am using nRF52-DK to deploy my programs. I try to use writing to SD card in ble_app_uart_central example. Both fatfs and ble_app_uart (central) examples work...
What are the memory settings in the SES compiler to compile secure_bootloader_ble_s140_pca10056
When I try to merge:
mergehex --merge s140_nrf52_7.2.0_softdevice.hex target_application...
I want to write some values to flash before the watchdog resets. For this I have the watchdog event handler specified:
In the wft_event_handler function I write a struct...
When trying to generate a new project Segger Project for my Project
in the option "Extra CMake Build Options" want to pass something like -DCONF_FILE='prj_test.conf' -DDTC_OVERLAY_FILE...
Hi Nordic team,
Looks like the most recent nrfjprog now supports flashing modem firmware.
I tried it and got some errors. Could you please point me in the right direction...
Dear Nordic Team Support
We face an issue where on different computers, using the same setup, different throughput can be achieved.
Setup:
- Custom Device using the...
Hello community...
I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful.
However, the...
