Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello, is it possible to use the nRF Connect desktop app with any standard bluetooth low energy dongle, rather than the nRF52840 dongle or the nRF52 development kit? I would...
Hi, I've got a project runing fine on v1.5.1 but will not update to v1.6.1 with this west.yml file: changing the revision v1.5.1 to v1.6.1 to keep up to date with the sdk...
Hello,
I am using nrf52 DK to program an nrf52805 with the ESB protocol. My nrf52805 is in slave mode compared to a micro Stm8l serial connected.
I'm having trouble configuring...
Hi everybody,
I am working in a project where there are one central_UART with multilink and diverse peripheral.
The devices are a custom board Fanstel BC840, nRF Connect...
Hello ;
We used NRF9160-SICA-B1A-R in our project. We have to choose the old version (NRF9160-SICA-R7) as NRF9160-SICA-B1A-R is out of stock. the only difference, Some of...
Hello,
I am attempting to implement cell tower triangulation using unwiredlabs.com's api.
I have single-cell geolocation working. I am having trouble getting multi...
To measure the antenna in band 20, you can send a carrier in the frequency range from 832-862 with the command "AT% XRFTEST = 1,1,20,8320,0,1,4".
To measure the antenna...
Hi,
I am using nRF Mesh SDK 4.1 and nrf SDK 16. I started with the light switch client example on a DevKit.
I am trying to change the publication address of the client...
Hello, DevZoners!
Hope you all doing great!
I have 2 9160DK's and for a few weeks now I've been trying to connect to the LTE network and then connect to the nRF Cloud...
I have changed the ram start and ram size, but as soon as i am adding the 10th characteristic to my second custom service, the program is crashing? i've also changed BLE_GATT_DB_MAX_CHARS...
What is the maximum file size of the LTE Modem firmware update we can expect on the 9160 platform? I am trying to plan out our external flash size and partitions.
The...
I recently switched from 1.5.1 to 1.6.1 and I'm now finding the SLM is misbehaving.
When I try to send a large payload such as 933 bytes of data, I find the CTS signal goes...
I successfully built, run and tested the sample: gps on my nRF9160 DK , without using the SUPL client library.
I then tried to build and run this sample: gps with the SUPL...
