Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I am working with NRF52840 chip with SES 6.4. My application was initially developed for nrf52832 but ported to 52840 and stopped by vector catch in debug mode. I had no issue...
Hardware Setup:
Boar d: custom board using nrf5340dk_nrf5340_cpuapp
N CS Version: v3. 0.1 (upgrade d from v2. 4 where it was working)
Problem Description: After...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello forum ,
here i m using nrf52840 customized board ;my flash is w25q64 i need to set my flash for deep power mode (sleep mode ) ;as well i need to set my supply gpio...
Hi!
The Power Profiler II Kit is an awesome piece of gear! I love it and it almost replaces power supply and logic analyser on my bench for daily work.
Would it be possible...
Hello,
I'm trying to extend the k_sys_fatal_error_handler() function to shut down a power supply and turn on an LED in case of fatal error/exception. Unfortunately, these...
Hi the Nordic Team,
I am developing the SED product of Matter over Thread protocol, now I want to customize a Bluetooth Service and Characteristic for my company's Bluetooth...
Dear Nordic Team,
I've been working extensively on creating a custom sensor driver building on Zephyr's sensor API. Throughout this process, I've utilized many available...
HI
We are currently reviewing a problem with a product currently in mass production and would like to request your assistance.
1. Development environment
- nRF52832...
Hi all
SBOMs must be created in order to comply with the European Cyber Resilience Act (CRA) directive. Zephyr makes this very easy:
west spdx --init -d BUILD_DIR west...
I have been using the SDK example ble_app_proximity to flash my demo boards nRF52840 to do some RF PHY testing on Bluetooth advertising.
It was very easy in this example...
Hi, I'm developing a device that needs to be able to securely connect to a MQTT Broker using certificates signed by a CA. In short, I already have that working when connecting...
We are developing a new board based on the NRF9151 and would appreciate some guidance regarding the power supply design for the modem.
Specifically, we’re looking for documentation...
I would need to change the GPIO voltage of the nRF9161 (M1) from 1.8 to 3.0 VDC. On nRF9161-DK schematic I see that VDD_GPIO can be isolated from nPM1300 (U9) VOUT1 by cutting...
Hi Nordic,
I am currently working with the nRF5340 and trying to understand the process of building applications in a multi-core setup.
From both the forum and official...
