When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
Hi, I am really confused about the Nordic SDK and way of doing things... I have seen so much conflicting documentation.
I am using SDK_for_Thread_and_Zigbee_v4.1.0 (currently...
my project is to send pressure data from one device to four other devices, it is medical field, previously i worked in nordic openthread udp protocol using nrf52840 for mesh...
Hello
Created in SDK v17 and simple_timer example. I made a simple code to control the LED using a timer. Every 500 milliseconds, the LED turns on sequentially. LED ON and...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
https://infocenter.nordicsemi.com/topic/nwp_034/WP/nwp_034/nwp_034_intro.html?cp=16_2
download PDF link not working. Perhaps replaced with other white paper(s)?
Thank...
Hello!
I have the following component in my device tree:
I would like to retrieve the PWM device and the associated pin number (pwm1 and 0x14). I tried:
Which...
Hello,
I am trying to develop a firmware to read pulse oximetry and heart rate data from this Sparkfun module (SEN-15219): https://www.sparkfun.com/products/15219
The...
Hi,
We mainly need AWS_Jobs, FOTA, Low Power, GPS, ADC, GPIO, certificate updates and whatever is related.
Currently we working on a project that uses:
- nRF9160 ...
Hi All:
I am trying to develop a project based on Heart Rate example. SDK version is 17.0, the receiver software is based Android-nRF-Toolbox.
Now, I can transfer ADC...
We are observing unexpectedly low throughput on the Mesh GATT Proxy service. Specifically, the Nordic device (acting in the GATT server role) is only sending one PDU on every...
Hi,
I have been looking into connecting two development boards over BT.
Previously, I managed to connect an nRF52833DK to an nRF9160DK.
https://devzone.nordicsemi.com...
Hello,
I am trying to enable the read protection on the NRF51822 on a custom board. By looking through the forums, I found different ways to try and enable the read protection...
