Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I want to run the board at 1.8V and run the uart and spi examples on my laptop. What should be my configurations and which micro-usb port shall I use to connect with laptop...
Hi,
I'm trying to send custom messages between server and client, based on the light switch example. I've modified button_event_handler and the client was able to receive...
Hi Nordic team,
I have an issue: I have to program/flash my mesh application together with softdevice140, mesh-bootloader and device settings page on the nrf52840 chip....
Hi everyone,
I am facing a kind of a strange problem. I want the system to enters system OFF mode when a certain pins goes to LOW. For that reason I have include code section...
I plan to use the nRF52833 or nRF52840 chip and as usual it needs a charger circuitry “PMIC” to charge the battery "Li-Ion"
Is there any special PMIC version recommended...
I'm using nRF52810 in a CR2032 battery powered device.
I use the DCDC mode to enhance power consuption. According to Product Specification in release 1.3 (and unlike nRF52840...
Hi,DevZone
I'm not Native English , sometimes can not express exactly, So, I'll provide a concise description about the question
1, platform: nRF52832_QFAA _E1, nRF5_SDK_13...
I used the NFR connect tool to install softdevice on the NRF52840 Dongle. I see noise about another tool to set up this kit in this forum; these are old. I forget what it...
Hello,
In our application, the central device will connect to one peripheral node at a time, collect the data, and disconnect it. There may be more than 30 to 40 peripheral...
Hi
I have two board nrf52833 along with the antenna array.
I want to implement Angle of Arrival.
I want to know from where can i start. any demo example
please me...
The global window in Nordic SES does not display the static global variables. I am probably missing something very simple, but I can't figure out how to view them when single...
At the very beginning of the program in the main function, my stack pointer is 0x20026390, although I expected it to be in the 0x20040000 area.
In this case, static memory...
Hi, I am using a thingy 52 board. I have Arm jlink programmer to load the program. And I have loaded the program successfully. But I want to debug the code. So, How can I...
Hi I looked at the lte_ble_gateway sample in the nrf connect sdk and noticed that we are able to simple call bt_ready() as if the nrf9160 is an nrf52 device. How is that possible...
Hi,
I have several timers and they will be app_timer_start() several time. I am not using APP_TIMER_MODE_REPEATED because they are not started immediately after they expire...
