When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I am trying to implement the communication between nrf52832 dk and nodemcu esp8266 over i2c.
My i2c code in nodemcu is working fine as I had tested the communication...
Using latest download of nrf Command Line Tools and a J-link Plus unit with Tag-Connect interface. Power on, all connections seem good. Trying to upload a .hex file through...
Hello, I am trying to implement some Bluetooth mesh functionality on my Thingy:52, and it's quite a daunting task.
I am using the mesh sdk v3.1.0 thingy:52 sdk v.2.1.0 and...
Dear All,
Could some one help to answer my commented questions below ? thank you so much !
1.
//Definition at line 743 of file hal_nrf.c .
uint8_t hal_nrf_read_reg...
Dears,
I am trying to implement a peripheral device which behaves like this:
1. within 30 seconds after powered up, the device can be discovered and connected by any other...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
Hi Nordic:
We are using mesh-sdk2.2, our application need a device can subscribe many group address, at the most we need 16 subscribe address in a model,
1. I'd like...
Hi all,
I get a really weird issue developing on the smart remote 3 project.
I work with my own hardware design, and as I want a specific behaviour I disabled power_management...
Dear friends,
Thanks all for your support.
I have used a button as a input to detect button press, while at the same time I am using the button as a system wakeup. ...
I'm using nrf51822 , softdevice S110 and the SDK10 . Im reading data from the sensor mpu9250 using i2c at 400Khz( Maximum) frequency. It taking more delay than expected to...
Hi!
I have been following this process to develop using armgcc and Eclipse: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/development-with-gcc-and-eclipse...
Hello,
I have been working to manipulate GPIO.
I succeeded to turn on and off P0.02 ~ P0.05 (LED 1~4). However, I cannot get P0.00 and P0.01 to get work.
GPIO IN seems...
Hi,
Now i am working on eddystone. It has Radio Tx power and Advertised Tx power in eddystone configuration service.
What is the difference between them?
I changed Advertised...
I'm using nrf_MESH app to provision proxy client in nrf_mesh SDK2.20.
There are some questions about provision process.
1).Before provision we know that the device should...
