When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi There,
I have developed an initial application on SDK11, based on the UART example, with Keil and it worked perfectly with the nice low power that you guys are capable...
Hi,
I have created a project with nRF52840 DK that reads sensors data and transmits them with BLE UART to my smartphone. Everything works fine.
Then, I tried to do the...
i am working on mesh application using two nrf51822 and one nrf2832. I started from light-switch examples. nrf51 set as two server and nrf52 as a client . In server side integrated...
Hi all,
in the datasheet of the nRF9160 is mentioned, that the same antenna can be used for LTE and GPS.
Page 364, chapter 8: GPS "Dedicated GPS antenna or shared antenna...
I'm using nRF52840 with SDK15.0.0
Following this tutorial : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial...
hi,
I'm trying to add a new BLE service to my device. I've followed the instructions in tutorial : devzone.nordicsemi.com/.../ble-services-a-beginners-tutorial , up to step...
Hello,
I have just started working with mesh and I'm using the 0.9.2 Mesh SDK. When I use the Serial interface (nrf_mesh_serial) I don't see any function about rx or rx...
Hi,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 3.1.0 and nRF5_SDK_15.2.0.
the data...
Hello!
I currently have 2 nR52DK using SDK14 and SDK15:
1) Beacon based on the beacon example
2) Central based on app blinky central + multirole
Then, I modified...
Hallo
I'm using sdk12 , S130 on NRF51822, so far successfully updated application, soft device and BL, however
lately after changing the size and starting address for...
Someone have a example of reading orientation sensor in javascript/HTML of the Thingy:52 equal of the github Nordic Example? github.com/.../Nordic-Thingy52-Thingyjs
Hello, I have a problem with staring "Run" in the "debugger mode" . I used Rigado evaluation board with BMD300 (nrf52) and also work with nrf5 SDK_15.3.0 Examples. Sometimes...
Hello,
I have 2 PCA10056 DK (with nRF52840), my purpose is to check the serialization between App. chip to connectivity chip
I have 2 problems on in each chip:
1. App...
I'm using the code below to enter lp mode;waiting for rtc wake up interrupt to wake up the mcu;
Now I need the app_timer module to do more things ,so I add app_timer lib...
Hi,
I'd like to add a cli command for entering DFU mode .
I'm using nrfConnect on a PC with USB.
When pressing the IF/BOOT button, I can enter DFU and can update the...
