Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I learning NRF52832 beacon using SDK15.2 i tested code ble_app_beacon code in non connectable beacon mode its working fine. how can i change this code like connectable beacon...
Hey, I would like to add BLE mesh functionality to my existing project which is based on the firmware v2.2.0 https://github.com/NordicSemiconductor/Nordic-Thingy52-FW . I...
I'm planning to connect The nRF52840 MCU GPIO in series to a 1.8V 20mA LED and a Resistor then to ground.
Would the current from the MCU be sufficient to power the LED ...
Hi,
Here is my issue, I don't enter in bootloader by using the buttonless DFU characteristic. Here below I expose my action and what it happens. Thank you in advance for...
Hi everybody,
This is my set-up : nRF5_SDK_13.0.0_04a0bfd, Eclipse 2019 03 IDE, NRF52832_xxAA, s132_nrf52_4.0.2_softdevice, windows 64 bits, NRFConnect 4.22.3, JLINK RTT...
Hello,
we have to integrate the nrf9160 into our own company internal build system / eco-system (freeRTOS based), e.g. not using the complete nordic sdk. As a starting point...
hello,
Now i want to adv only with 37 channel, i want to use SDK15.0.
i add m_adv_params.channel_mask[x] in advertising_init() as:
static void advertising_init(void...
Dear Sir:
I have met a strange problem when using ble_uart example code on SDK 10
1. SDK Version is SDK 10
2. Chipset is Nrf51802
3. the board with no external 32...
Hello Nordic Team, We are using nRF52840 ble chip with S140 nordic stack and SDK 15.2.0 on the SEGGER IDE installed on the Windows OS. We want nRF52840 chip to detect surrounding...
Hi,
I'm working on a project where I need to use an RNG.
I worked with the nrf_drv_rng function with previous SDK but in the latest SDK (15.3) the is nrfx and nrf drivers...
I've been chasing my tail trying to figure this out, and thought I'd have better luck making a post instead. I could REALLY use your help! If you can merely point me in the...
Hi, Considering the new Bluetooth spec. 5.1 and in particular the direction finding feature in the AoA architecture I am wondering if both the devices: the LE transmitter...
Hi, I want to create one system. When master writes data of Nordic, I receive callback with BLE_GATTS_EVT_WRITE case. Here I want to write return to master with success/ failure...
