When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I have Nordic NRF 52840 DK development board, using Ubuntu 18.04, I loaded "ble_connectivity_s140_usb_hci_pca10056" to the board successfully. Then I powered cycle and cannot...
My setup: Eclipse, nrf52832 on a custom target board, s132, SDK13
I am trying to implement the workaround for the problem described here:
https://devzone.nordicsemi.com...
Hi everybody,
I would like to know how the module nRF9160 comes from the factory in it default configuration.
Is it possible to use it in UART mode only with the pin 86...
Hey guys,
I am currently using the nRF24L01+ (more specifically the module that has +pa +lna), and I am experiencing some odd behavior. I will briefly go over the devices...
Before buying the Teledyne BPA low energy protocol analyzer, I asked a question here based on the Teledyne not supporting BLE 5.
I was told that it would work fine with...
Hi all, I'm working on creating new model for sending a byte from proxy client based on Generic On Off model. For working with light-switch proxy example , I used NRF Mesh...
Hi,
I am developing a sensor application with the nRF52832 on a custom board.
Therefore I designed a GATT with nRF5_SDK_14.0.0 softdevice which exposes 3 custom characteristics...
I’ve downloaded nRF5_SDK_11.0.0_89a8197 and starting with examples from \examples\ble_peripheral\???\pca10040\s132\arm5_no_packs\
I would like the other device to request...
I want to interface ADXl345 with nrf51 SDK. suppoose my device address is 0x53 and register address is 0x2D and i want to write value 8. now nordic i2c has function nrf_drv_twi_tx...
Hi We have a generated a key pair using ECDSA secp256k1 ```
err_code = nrf_crypto_ecc_key_pair_generate ( NULL , & g_nrf_crypto_ecc_secp256k1_curve_info , & private_key...
I'm trying to run a project baset on the ble_app_proximity example project . When I trying to call a nrf_sdh_enable_request() function library goes into an infinite loop....
Hello,
I would like to know if you can point me where to find the electrical characteristic of the module nRF9160. I'm looking for :
- Then maximum current the module...
I work on your new Mesh SDK 3.1.0 and I have some questions for you.
First it is about DFU over Mesh. I think your documentation is very weak. I understand that they are...
Hello Nordic, we use the nrf52 proprietary protocol in the project, it will send 200 data per second, and no ack confirmation, the application data length is 25 or 32 bytes...
