Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Installed nRF5_SDK_15.2.0_9412b96 and nRFGo Studio. nRFGo Studio fails to recognize the nRF52840 DK board. Screen like this:
It sees and correctly identifies the Segger...
I am trying to do things like
get the current date and/or time
configure a socket
activate a socket
Usually I use commands like
at+cclk
at+csdf
at+ctzu...
I am following the Thingy:52 "Compiling With Keil" instructions provided in the following link.
nordicsemiconductor.github.io/.../firmware_compile.html
However, I get...
Hi,
We have released multiple products with the NRF52832 chip with SDK's ranging from 10.x to 14.x, quite successful so far.
However, one part that is lacking in my opinion...
I have been struggling with getting nrfjprog working on CentOS 7.x. Each invocation results in the following error due to the version of glibc used to link the nrfjprog binary...
Hello!
A quick question about how to shutdown unused RAM on the nRF52810-CAAA?
We're not using any of the Soft Devices. Our code is pretty tiny. Map file attached.
We...
Hi,
I want to read data from my ble UART (NUS), to do that I implemented the NUS service and registered the onDataWritten callback (which is the MBED equivalent of the HVX...
Hello:
If we are to use the nrf9160 in a production product, what additional certifications are required? For example, if I purchase a Telit cellmodule, I still have to...
Hello All,
I want the DFU service at the application level, not at the bootloader level. Means I have to build a very simple bootloader but I want DFU service at the application...
Hello nordic:
nrf52832 how to control pa, i use this functio pa_lna_assist(). This function is the solution on BBS.this used for s132,but i use s332.the ble is ok,but the...
As per description, I don't understand how to make a dfu package that writes the whole MBR+Application range and doesn't use a SoftDevice, for example out of a hex file such...
I'm using SDK 15.2 and trying to set up a USB mic class. I am having trouble getting the SOF audio interrupt to fire.
I initialize the app_usbd module with the configuration...
Hi
I would like to know that is there any Blue tooth low energy relay like RFID tag , which can detect bLE only and can trigger a circuit. It should have small form factor...
Hello everyone , i have noticed that the sniffer can pick up the the packet from the same channel twice.
According to the Bluetooth 4.2 specification, the advertisement...
Hi all,
We were developing our application using nRF52840 and later decided to change to nRF52832 considering our hardware constraints. nRF52840 has 16 bit counter for EasyDMA...
