Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Help, I want to run NRF_LOG_ENABLED builds but occasionally I want the device to sleep for (many) minutes, so I wish to turn off the NRF_LOG_UART backend since it consumes...
I plan to test BLE and Zigbee communication range in multiprotocol examples.
And I haven't found how to configure Zigbee tx power.
Questions:
1. Is the tx power of BLE...
Hi all,
I am trying to interface HI-3585 with nrf52832 through SPI which works fine. Now i have merged the code with saadc program so as to transmit adc values through HI...
Hello.
I am building nRF Mesh SDK using cmake (gcc).
After successful building the code, I flashed hex file to nRF 52 DK.
I want to know free space in DK after flashing...
We want to use nRF52840 as advanced USB - UART converter to control end device (see structure below).
We already checked that our end device is working fine by external...
Dear Support
I’m having a problem erasing the network configuration data in the flash.
We are using nrf5_SDK_for_Mesh_v2.0.1 with the flash manager according to this post...
I am new and trying to install and run samples on Raspi 3B but cannot. Have anyone worked with Raspi 3B and nrf52840 dongle and please give me some instructions.
Hi I'm using Android Studio 3.2 and github.com/.../Android-nRF-UART My Samsung SM-G570Y (Android 7.0 API 24) works no problems but the Samsung SM-G955F (Android 8.0.0, API...
Hi. I am developing a gateway using SDK15 and nRF52840.
I'm advertising 4 devices every 20ms.
Theoretically, it should be scanned 50 times each, but in reality it is...
I tried to add an additional characteristic to NUS service as below.
However, any mobile apps could find only existing Nordic Rx and Nordic Tx characteristics, other than...
- Go to the following link:
www.nordicsemi.com/.../
- Scroll down the page and click the "Downloads" tab
- Go to the nRF52840-DK-HW tab and click "Download file"
...
Dear Nordic Team
-> what is the pinout of the TRACE connector of the nrf52840DK (PCA10056) board ?
I need to connect wires onto P0.11 and P1.00 GPIO, and the trace...
I'm using the nRF52832 SoC through Rigado's BMD 350. For initializing BLE, I'm using the Thingy52 firmware code as the hardware mostly reflects that of the Thingy52. My hardware...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am receiving data from the sensor with TWI communication and writing it to the sensor by SPI communication...
Hi everyone,
Device : nRF52832
SDK version : 14.2
Softdevice : S132 v5.0
I am facing a problem when changing the interrupt priority dynamically. Let me explain the...
